background image

12 

 

  Firstly, slide the clean dry quartz glass sleeve into the unit. 

 

Locate the ’O’ rings carefully on the ends of the quartz sleeve.  

  Make sure the threads are clean, wipe a little silicone grease onto the threads. As these threads 

are only serviced periodically, this lubrication will help to prevent them binding together. 

  Hand tighten the blue quartz sleeve locking nuts onto the unit. Be sure not to overtighten as this 

can damage the quartz sleeve. 

  Replace the UV lamp(s) with a new one(s) and reconnect blue lamp holders. 

 

NOTE:

  To  avoid  bending  the  lamp  pins  during  the  reassembly,  pull  the  plastic  fitting  out  of  the 

shroud. Connect it to the lamp and push the shroud back in to place. 
 

 

 
 

NOTE: 

Pinch  the  blue  lamp  holder  shroud  as  you  reassemble  the  unit  to  release  any 
trapped  air.  Failure  to  release  the  trapped  air  may  cause  the  lamp  holder  to 
disconnect from the lamp end. Turn on the water supply to check for leaks before 
reconnecting the electric supply.  

 

Important:  

The plastic body and blue compression fittings have been manufactured from polymers that 
have been specifically stabilised to protect them from the effects of the UVC emitted from 
the UV lamps. Despite this UV protection they will be eroded by a combination of the UVC 
and water flow. As a matter of course they should be inspected whenever a lamp change 
is carried out, to ensure they are not showing excessive wear and tear. Replacement parts 
are available.

 

 

6.  DISPOSAL OF ELECTRICAL/ELECTRONIC EQUIPMENT 

 

 

DO NOT dispose of this product as an unsorted municipal waste. 

 

This  symbol  on  the  product  or  on  the  packaging  indicates  that  this  product  should  not  be  treated  as 
household waste.  Instead it should be handed over to the applicable collection point for the recycling of 
electrical and electronic equipment. 
 

 

 
 

 
By ensuring this product is disposed of correctly you will help prevent potential 
negative  consequences  for  the  environment  and  human  health,  which  could 
otherwise  be  caused  by  inappropriate  waste  handling  of  this  product.    The 
recycling of materials will help to conserve natural resources. 
 
For  more  information  please  contact  your  local  Civic  Office,  household  waste 
disposal service or the retailer where the product was purchased. 

Summary of Contents for H.R.UV-C SPA-STANDARD

















Reviews: