background image

 

 

Fig. 7

 

 

All factory unions are made from ABS plastic, when gluing connections to an ABS pipe an ABS cement 
must be used or when using a PVC pipe, a Transition cement must be used (See Fig. 7). 

 

There is no need to use mastic or PTFE tape to connect unions to the device, use the O-rings provided to 
put in the groove on the end of the Manifold Assembly. 

 
NOTE:
    Be sure to apply the glue evenly and to all surfaces that will be in contact to reduce the

 

risk of leakage. 

 
 

3.6 Electrical connection 

 

WARNINGS:
 

 

  This  device  must  be  installed  by  a  qualified  Electrician  following  the 

instructions provided in this manual. The manufacturer will not be liable 
for any issues caused by poor or improper installation.

 

  Any alterations made to the unit (unless stated) will affect the warranty. 

This  also  applies  if  components  are  changed  for  non-standard 
components acquired anywhere other than direct from the manufacturer.

 

  Incorrect installation may result in serious damage to property/persons.

 

  The  device  must  be  installed  in  accordance  with  the  country/regional 

requirements  and  regulations  and  an  Electrical  Installation  Certificate 
must be provided on completion of the installation.

 

  The power supply must be fitted with a 30mA RCD. 

  Never look directly at an illuminated UV lamp. 

 

 

WARNINGS:
 

 

  This  device  must  be  installed  by  a  qualified  Electrician  following  the 

instructions provided in this manual. The manufacturer will not be liable 
for any issues caused by poor or improper installation.

 

  Any alterations made to the unit (unless stated) will affect the warranty. 

This  also  applies  if  components  are  changed  for  non-standard 
components acquired anywhere other than direct from the manufacturer.

 

  Incorrect installation may result in serious damage to property/persons.

 

  The  device  must  be  installed  in  accordance  with  the  country/regional 

requirements  and  regulations  and  an  Electrical  Installation  Certificate 
must be provided on completion of the installation.

 

  The power supply must be fitted with a 30mA RCD. 

  Never look directly at an illuminated UV lamp. 

 

Summary of Contents for H.R.UV-C SPA-STANDARD

















Reviews: