21
EN
ET083 2G/3G COMMUNICATOR V1.0
7.2. Advanced Mode
The communication method of Advanced mode is selected using
ELDES Configuration Tool
software.
Advanced
mode features the following com-
munication methods:
•
Voice Calls
•
SMS
•
IP
•
CSD
•
PSTN*
Advanced mode supports 1 primary and up to 2 backup connections. All of the aforementioned communication methods can be set up as primary
or backup connection in any sequence order.
Initially, the device communicates via primary connection with the monitoring station. By default, if the initial attempt to transmit data is unsuc-
cessful, the device will make additional attempts until the data is successfully delivered. If all attempts are unsuccessful, the device will follow this
pattern:
a) The device switches to the backup connection that follows in the sequence (presumably - Backup 1).
b) The device then attempts to transmit data by the backup connection.
c) If the initial attempt is unsuccessful, the device will make additional attempts until the data is successfully delivered.
d) If the device ends up with all unsuccessful attempts, it will switch to the next backup connection in the sequence (presumably - Backup 2) and will
continue to operate as described in the previous steps. The connection is considered unsuccessful under the following conditions:
•
IP
– The device has not received the ACK data message from the monitoring station within 40 seconds.
•
Voice calls:
◦
The device has not received the “handshake” signal from the monitoring station within 40 seconds.
◦
The device has not received the “kissoff” signal from the monitoring station within 5 attempts each lasting 1 second.
•
CSD
– The device has not received the ACK data message from the monitoring station within 35 seconds.
•
SMS
–The device has not received the SMS delivery report from the SMSC (Short Message Service Center) within 45 seconds.
e) If one of the attempts is successful, the device will transmit all queued up data messages by this connection.
f) The device then returns to the primary connection and attempts to transmit the next data messages by primary connection.
g) If the device ends up with all unsuccessful attempts by all connections, it will return to the primary connection.
* When Advanced KissOff mode is enabled. For more details, please refer to
19. ADVANCED KISSOFF MODE
.
Once enabled, Advanced mode overrides the jumper position on
SET/MODE
PCB pins.
7.2.1. Voice Calls Method
Based on the communication wiring method that is being used, using this method the communicator:
•
RING/TIP interface
– Retrieves Ademco Contact ID or Scancom data from the alarm panel, saves it to the memory buffer (the data may be
stored for up to 10 seconds) and transmits it to the monitoring station via 2G/3G audio channel. Before proceeding with any further configura-
tion, please complete the steps provided in
6.1. RING/TIP Interface
.
•
Keybus or Serial interface
– Retrieves serial data from the alarm panel, converts it into Ademco Contact ID data followed by transmission to
the monitoring station via 2G/3G audio channel. Before proceeding with any further configuration, please complete the steps provided in
6.2.
Keybus and Serial Interfaces
.
To set the communicator to transmit data using this communication method, please proceed as follows:
1. On alarm panel*: enable Ademco Contact ID or Scancom mode.
2. On alarm panel*: Set valid Account number..
3. On alarm panel*: Set the monitoring station phone number (-s) in one of the following formats:
•
International (with 00)
– The phone numbers must be entered starting with 00 and an international country code in the following format:
00[international code][area code][local number], example for
UK: 0044170911XXXX1
.
•
Local
– The phone numbers must be entered starting with an area code in the following format: [area code][local number], example for
UK:
0170911XXXX1
.
4. On eT083: Connect the device to the computer via USB cable and run
ELDES Configuration Tool
software.
5. On eT083**: Open
System → Security Panel Settings
and set the monitoring station phone number.
6. On eT083: Open
System → Settings
section and proceed as follows:
a) enable
Advanced Mode
.
b) Set
Voice Calls
as
Primary
connection. In addition,
Backup 1
and
Backup 2
connections can be set under this section.
7. On eT083: Open
Voice Calls Settings
section and select protocol:
