Eldat Easywave RCR02E5002A01 Manual Download

Page: 6 / 8

Deleting the Transmitter

In delete mode, individual transmitters can be de-

leted from the memory of an output.

Operation

[Press button]

Display

Note



1x briefly or

2x briefly

LED 2TB flashes

LED 1TB flashes

Programming mode started.



repeatedly

Select delete function L.



1/2/3/4

LED 1/2/3/4 and

LED xTB flash

Select output. Only one output can be

selected. Output can be changed as often as

required.



until

LED output and 2TB

and 1TB flash quickly

Delete mode started.

Cancel 1x

<1.6 s

(> 1.6 s)



Transmitter button

LED output and 2TB

and 1TB light up

Transmitter deleted from the selected output.

When all the LEDS go out, the receiver is

ready for operation.

1x briefly

1) If no buttons are pressed within 30 seconds, the RCR02 automatically switches back to operating mode.

The settings are not saved.

RESET

A reset must be performed individually for each

output.
All programmed transmitters are deleted and all

switching times for the respective output are re-

set.

Operation

[Press button]

Display

Note



1x briefly or

2x briefly

LED 2TB flashes

LED 1TB flashes

Programming mode started.



repeatedly

Select delete function L.



1/2/3/4

LED 1/2/3/4 and

LED xTB flash

Select output.

Only one output can be selected. Output can

be changed as often as required.



until

LED output and 2TB

and 1TB flash quickly

Delete mode started.

Cancel 1x

<1.6 s

(> 1,6 s)



until

LED output ans 2TB

and 1TB light up

All transmission codes from the selected

output are deleted and the TIMER is reset.

When all the LEDS go out, the receiver is

ready for operation.

(> 1,6 s)

1) If no buttons are pressed within 30 seconds, the RCR02 automatically switches back to operating mode.

The settings are not saved.

Programming

If a transmitter is programmed in several outputs, it must be deleted individually from each

output as necessary.
If an attempt is made to delete a transmitter that is not programmed into the selected output,

the LEDS flash quickly and the receiver remains in delete mode.

1/2/3/4

Select operating

mode L

Start program-

ming mode

Start delete

mode

Select output

Send transmission code

Summary of Contents for Easywave RCR02E5002A01









Search results

Summary of Contents for Easywave RCR02E5002A01

Reviews:

Related manuals for Easywave RCR02E5002A01

Brands by name

Popular brands

Eldat Easywave RCR02E5002A01, Manual

Search results

Summary of Contents for Easywave RCR02E5002A01

Reviews:

Related manuals for Easywave RCR02E5002A01

Brands by name

Popular brands