Intended Use
The device is intended for mounting on a DIN rail
in a distribution box or a control cabinet in dry
rooms. The unit may only be used as a wireless
receiver for activating electrical devices in accord-
ance with the load table. To be operated with Ea-
sywave wireless transmitters.
The manufacturer shall not be liable for any dam-
age caused by improper or non-intended use.
Safety Advice
Before installing the device, carefully
read through this operating manual!
Caution! Electrical installation must only be
carried out by a qualified electrician, failure
to do so may result in fire or electric shock.
Observe the applicable laws, standards and re-
gulations as well as the operating instructions of
the appliances to be switched!
This device is only intended for indoor use in
dry and dust-free rooms.
Have faulty devices checked by the manufac-
turer!
Do not make any modifications to the device!
Setting up the Receiver
A Installing the Receiver ..............................
1
A1 Mounting the Receiver ....................... 1
A2 Electrical Connection ......................... 2
B Operation
...................................................
2
B1 Operating and Display Elements ....... 2
B2 Operating Modes ............................... 3
B3 Conversion table for TIMER .............. 4
C Programming
............................................
5
C1 Programming the Transmitter ............ 5
C2 Setting the TIMER...............................5
C3 Deleting the Transmitter ..................... 6
C4 Reset ................................................. 6
D General Information
..................................
8
A
Installing the Receiver
A1
Mounting the Receiver
The device is intended for installation on a stand-
ard DIN rail (35 x 7.5 mm). Pull out the slide to
allow fixing through mounting points.
Only a qualified electrician may install, connect
in accordance with the connection diagram and
set up the receiver.
Please note the „5 safety rules“ for electri
-
cians!
1. Switch off the power supply. Follow the „5
safety rules“!
2. Mount the RCR02 onto the rail.
3. Connect the cables for the power supply and
for the devices in accordance with the con-
nection diagram (see page 2).
4. Switch on the supply voltage. Follow the „5
safety rules“!
5. Programme the receiver according to the op-
erating manual (see pages 4-5).
In unfavourable environmental conditions, the ex-
ternal antenna ACC-ANT50-03-21P can be used
to improve wireless reception. This is not included
in the delivery and can be ordered separately.
RCR02E5002A01
2TE
Technical Data
Frequency:
868.30 MHz
Modulation:
FSK
Coding:
Easywave
Power supply:
230 V AC 50 Hz
Output:
2 potential-free relay
contacts 16 A
(normally open)
Power consumption:
0.6 W standby
Connected load:
see Load Table
Operating temperature: -20 °C to +60 °C
Dimensions (W/L/H): 34.5 /89.6/62.8 mm
Weight:
108 g
Load Table
Load type
max. load
Ohmic load:
Incandescent lamps, 230 V
halogen lamps etc.
16 A / 3,680 VA
IInductive load:
Halogen lamps with wound
transformers (transformer at
least 85% loaded)
3 A / 690 VA
Non- or serial-compensated
fluorescent lamps with ferro
-
magnetic ballasts
3 A / 690 VA
Parallel-compensated fluores
-
cent lamps with ferromagnetic
ballasts
3 A / 720 VA
Electronic ballast capacity:
electronic ballasts, electronic
transformers, etc.
4 A / 920 VA
Function
The RCR02E 2TE DIN rail receiver is used for the
potential-free activation of two mains-powered
devices.
The receiver can be operated in ON/OFF, PULSE
and DEAD MAN‘S SWITCH modes. The ON/OFF
mode can also be used with two TIMER functions
and a LOGIC function.
Scope of Delivery
DIN Rail receiver RCR02 2TE,
operating manual
DIN Rail receiver RCR02
EN
RCR02E5004A01
4TE
Technical Data
Frequency:
868.30 MHz
Modulation:
FSK
Coding:
Easywave
Power supply:
230 V AC 50 Hz
Output:
2 potential-free relay
contacts 16 A
(normally open)
2 potential-free relay
contacts 16 A
(change-over)
Power consumption: 0.6 W standby
Connected load:
see Load Table
Operating temperature: -20 °C to +60 °C
Dimensions (W/L/H): 70.5 /89.6/62.8 mm
Weight:
186 g
Load Table
Load type
max. load
Ohmic load:
Incandescent lamps, 230 V
halogen lamps etc.
16 A / 3,680 VA
IInductive load:
Halogen lamps with wound
transformers (transformer at
least 85% loaded)
3 A / 690 VA
Non- or serial-compensated
fluorescent lamps with ferro
-
magnetic ballasts
3 A / 690 VA
Parallel-compensated fluores
-
cent lamps with ferromagnetic
ballasts
NO
3 A / 720 VA
NC
1.5 A / 345 VA
Electronic ballast capacity:
electronic ballasts, electronic
transformers, etc.
4 A / 920 VA
Function
The RCR02E 4TE DIN rail receiver is used for the
potential-free activation of four mains-powered
devices.
The receiver can be operated in ON/OFF, PULSE
and DEAD MAN‘S SWITCH modes. The ON/OFF
mode can also be used with two TIMER functions
and a LOGIC function.
Scope of Delivery
DIN Rail receiver RCR02 4TE,
operating manual
Models
1
