background image

V

V

I

I

P

P

C

C

L

L

A

A

M

M

P

P

M

M

I

I

N

N

I

I

MIN/ MAX Mode:

- Accuracy: same as previous table +0.3% L

- Capture time: 100 ms typ. (every 400 ms)

3.9 Power factor calculation (PF)

With the clamp configured in power measurement (switch on position 

W

) and correctly connected (see § 3.8),

perform a short press on the yellow key: the power factor is displayed.

Display range

Measuring range(1)

Accuracy

Resolution

0,20 a

0,49

0,50 a

1,00

5% L +2 pt

1,00

0,01

5% L +2 pt

Characteristics

(1) The display of the power factor is limited to 1.00 If one of the terms of the power factor calculation is outside its

power range, the display of the power factor indicates an indeterminate value”

- - - -

”.

MIN/ MAX Mode:

-Accuracy: Same for the table below + 1 pt

-Capture time: 100 ms typ. (every 400 ms)

3.10 Frequency Measurement (Hz)

This function is active for measurements V, A, W in AC. For the power function, the frequency measurement is

performed on the voltage signal.

1. 

Perform a short pressing on the Hz key, the display shows the frequency of the measured signal.

2.

 Pressing again returns to the previously displayed measurement.

Display range

40 Hz

Measuring range(1)

Accuracy

Resolution

10,00 a

39,99 Hz

0,4% L +1 pt

0,01 Hz

400 Hz

4000 Hz

Triggering threshold (2)

5V ou 10A

0,1 Hz

1 Hz

40kHz

40,0 a

399,9 Hz

400 a

3999 Hz

4,00 kHz a

19,99 Hz

10 Hz

1) Below 5 Hz, the display shows 

0.0

(2) Below the triggering threshold, the display shows an indeterminate value (- - - -

).

MIN/MAX

- Accuracy: same as in the table above +0.2% of reading with limitation to 5 kHz.
- Capture time: 125 ms typ. every 400 ms

3.11 Phase order indication

This measurement is performed with 2 cables only, sequentially as follows:

1.

 Integration of a “reference” period on one phase L1-L2 for example

2.

 Integration of a “reference” period on one phase L1-L3

3.

 Calculation of the time delay between “reference” and “measurement” periods enabling determination of the phase

order or phase rotation direction.

7

Characteristics

Summary of Contents for VIP CLAMP MINI Series
















Reviews: