background image

V

V

I

I

P

P

C

C

L

L

A

A

M

M

P

P

M

M

I

I

N

N

I

I

-

 

Special reference condition

-3-phase and sinusoidal network with 50 Hz or 60 Hz stable frequency

Characteristics

-  Frequency range: 47 Hz to 53 Hz or 57 Hz to 63 Hz.

-  Acceptable voltage range: 50 V to 600 V

-  Acceptable phase imbalance rate: ±10°

-  Acceptable amplitude imbalance rate: 20%

-  Acceptable voltage harmonic distortion: 10%

Running of phase rotation direction detection sequence

Note 1:

In the following table, display of the symbol                refers systematically to the beginning of sequence

Note 2:

The sequence of the following table is described using:

- L1 on terminal “COM”

- L2 then L3 on terminal “+” The same result is obtained if:

- L2 on terminal “COM” , L3 then L1 on terminal “+” or:

- L3 on terminal “COM” , L1 then L2 on terminal “+”

Note 3:

The measurement principle is based on a certain frequency stability and practically sinusoidal signals (THD < 10%).

This excludes in particular measurement on power generators whose spin stabilisation system is too weak to ensure

adequate frequency stability.

3.12 Secondary Functions

3.12.1 Display lock

A short pressing on the 

HOLD 

key freezes the display.

A second pressing unlocks the display.

3.12.2 Preselection of MIN/MAX mode

A short pressing on the 

HOLD

 key then on the 

MIN/MA

X key preselects the MIN/MAX mode. A second pressing

on the HOLD key makes the MIN/MAX mode effective.

This function is used to select the MIN/MAX mode upon request to prevent, for example, the unwanted or mistaken

integration of MIN/MAX values.

Action

Display

Switch on the position 1 2 3 

Press the yellow key

Cable connected black on

L1 and contact

displays red cable on L2

Comments

Red cable contact on L3

 (less than 10 seconds

after leaving L2

rEF

ErrV 

(2 s)

poi 

Err Hz 

(2 s)

poi 

rEF OK

MEAS

ErrV 

(2 s) then

Err Hz 

(2 s) then

Err 1.2.3

3.2.1

Enter the function

The unit is ready to detect the

reference period

The unit determines the period

measurement, the following messages

may be displayed (after 10 s max):

-- determination of period for

    measurement in progress

-- ontact on L3 a was performed too late

   (more than 10 s after display rEF OK)

-- voltage incorrect

-- equency incorrect

-- dtermination of phase direction

    impossible

-- direct direction of phase rotation

-- reverse direction of phase rotation

Return to beginning of sequence

(valid at all times in the sequence)

Press yellow key

8

after 10 seconds maximum result is one

of the 3 following opposite:

-- if voltage < 50 V

-- if niminal freq.50 Hz or 60 Hz

-- re

ference period correct

Summary of Contents for VIP CLAMP MINI Series
















Reviews: