background image

25

B) DISPLAY BACKLIGHTING

The SETUP MENU is added with a Setup page on
display backlighting control with commands DISP
ON, DISP  OFF and DISP AUT (automatic
backlighting for 10 seconds at each keystroke).  The
life of the battery is about 45 hours with DISP ON
(the first five hours of which with backlighting on
and the following 40 hours with backlighting off) and
approximately double with DISP OFF.

C) RESTORE DEFAULT SETUP PARAMETERS

The SETUP MENU includes the possibility to restore
the default settings by using a command (TV ratio,
TA ratio, Configuration setup, Harmonics setup,
COM Setup).

D) DISPLAY OF ACTIVE POWER MEASURE OF

SELECTED HARMONIC

In the page displaying the RMS values relative to
the harmonic selected, there is now the possibility
to see the Active Power value (besides the values
of V, I and Power Factor) by keeping the Sel key
pressed.

24

This function allows you to store in a special flash-
type auxiliary memory (1024Kbyte) the entire range
of measures managed by NANOVIP PLUS, with a
maximum of 4032 recorded blocks of measures at
intervals from 2 second to 1...99 minutes.

The campaigns are recorded through the menu.

The SETUP MENU allows access to 4 pages for
setting data recording functions:
• Date setup
• Time setup (date and time are included at the top

of every record)

• Setup of the time interval between two recordings

(every 2 seconds, or at  intervals of 1...99 minutes)

• Deletion of recorded data.

In the LOG CTRL MENU the recording of the
measure campaigns can be activated or deactivated;
this menu also displays the percentage recorded in
memory and the programmed rate of recording.
Once activated, the data LOG continues until it is
either deactivated or the memory is full: during this
time the part of the Setup menu relative to the LOG
(see the block diagram on the menu pages) is
deactivated; if the device is turned off and then
tur ned on again recording star ts again.

In the MEAS PAGE two more pages are included
with display of the date and time.

To download data by serial line, see the dedicated
section.

A) RECORDING OF MEASURE CAMPAIGNS

(operation)

ENGLISH

Summary of Contents for NanoVIP Plus Mem












Reviews: