ELCOM Euro-500 Handy Series Service Manual Download Page 47

Page: 47 / 80

Euro-500TX Handy

Service manual

Euro-500TX Handy

Service manual

Note 1: External drawers with solenoid current greater than 1 A are not recommended.
Note 2: In order to prevent any trouble it is recommended to use only the drawers offered in the Euro-500TX

Handy distribution network.

1. Turn the ECR off.

2. Ready the ECR drawer.

3. Remove the original connector.

4. Press the new connector as shown in the figure.

5. Plug the drawer connector into the rear connector panel for external devices.

6. Turn the ECR on and check the drawer functionality (e. g. press “Drawer open” in the registration

or training mode, event. use test #600).

Note 3: The drawer opens automatically only if the ECR is externally powered.

4 3 2 1

1 4

Top view

Front view

ECR drawer cable

Fig. 4.20 Connection of the external ECR drawer

Fig. 4.21 Modular jack 4×4 connexion

Summary of Contents for Euro-500 Handy Series
















































































Search results

Summary of Contents for Euro-500 Handy Series

Reviews:

Related manuals for Euro-500 Handy Series

Brands by name

Popular brands

ELCOM Euro-500 Handy Series, Service Manual

Search results

Summary of Contents for Euro-500 Handy Series

Reviews:

Related manuals for Euro-500 Handy Series

Brands by name

Popular brands