background image

Caution

1. Do not expose motor to humid or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna and keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If power cable or connector is damaged, do not use.
6. Ensure correct crown and drive adaptor are used.
7. Ensure power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls shall be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered
operation.
11. Installation and programming to be performed by a qualified professional, use or modification outside
the scope of this instruction may void warranty.  

Charging Instructions

Charging: 

12.6V 1A

This motor has a 12V built in Li-ion battery pack with integrated charge management.
Maximum charger charging input: 

12.6V 1A

Before first use please charge motor for 6 hours. 
During operation, motor will stop running when the voltage is lower than 8.0V and it will resume again when
the voltage is greater than 8.5V.
During operation, motor will stop buzzer sounds when the voltage is lower than 7.0V and it will resume again
when the voltage is greater than 7.5V.
When the motor is running continuously when the voltage is lower than 10V, the buzzer sounds 10 times.

Solar (PV) Panel: 

16V~24V

Charger port

and solar panel

charging port

Motor Installation

Drive tube

Drive tube

Step 1  Cut drive tube to required length.

Step 3  Mount correct crown & drive adapter on

the motor. Make sure drive adapter fits firmly and

crown rotates freely.    

Step 4  Align the notches on the crown and drive

adapter with the drive tube, slide and fit the motor  

into drive tube. Mount idler and bracket on both

ends.  

Step 2  Ensure tube edge is clean and burr-free.

Drive Adapter

Crown

Circlip

Bracket

Bracket

Attention

Fields of Application

Features

The motor is suitable for motorization of roller blinds. 

Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.
Important safety instructions to be read before installation. 
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

Built-in Receiver
Jog & Tilt
Built-in Lithium Battery
Scan and Program
Solar Charging

Switch Direction
Stall Protection
Program Button
Reset to Factory Mode
Status Feedback

Electronic Limit
Preferred Stop Position
Speed Regulation
Scene Control
Memorized Setting

Specifications

Working Temperature: -10

℃ 

~ +55

Rated Voltage: DC 12V

Radio Frequency: 433.925MHz

Maximum Running Time: 6 minutes

DM35LE/S-3/28

3

28

2.2

DM35LE/S-6/24

6

24

3.23

DM35LE/S-13/13

13

13

3.23

DM45LE/S-20/10

20

10

4.1

DM45LEQ/S-3/28

3

28

2.2

DM35LEQ/S-2/28

2

28

1.16

DM45LEQ/S-10/9

10

9

2.2

Following data for reference

* For reference only.

Model

Rated Torque

(N.m)

Rated Speed

(rpm)

Rated Current

(A)

DM35(45)LE/S

DM35(45)LEQ/S

Instruction

A-04

SAFETY  NOTE

1. This appliance can be used by children aged from 8 

    years and above and persons with reduced physical, 

    sensory or mental capabilities or lack of experience 

    and knowledge if they have been given supervision or 

    instruction concerning use of the appliance in a safe 

    way and understand the hazards involved.  

2. Children shall not play with the appliance.

3. Cleaning and user maintenance shall not be made by 

    children without supervision.

4. If the supply cord is damaged, it must be replaced by 

    the manufacturer, its service agent or similarly qualified

    persons in order to avoid a hazard.

5. WARNING: the drive shall be disconnected from its 

    power source during cleaning, maintenance and when

    replacing parts.

6. The instructions shall state that the A-weighted emis

    sion sound pressure level of the drive is equal to or 

    less than 70 dB(A), e.g. by writing LpA ≤ 70 dB(A).

7. The mass and the dimension of the driven part shall be 

    compatible with the rated torque and rated operating 

    time.

8. The type of driven part the drive is intended for.

9. WARNING: Important safety instructions. It is important 

    for the safety of persons to follow these instructions. 

    Save these instructions.

10. Do not allow children to play with fixed controls. Keep

    remote controls away from children.

11. Frequently examine the installation for imbalance and

    signs of wear or damage to cables and springs. Do not

    use if repair or adjustment is necessary.

12. Watch the moving shutter and keep people away until 

    the shutter is completely closed.

13. WARNING: Important safety instructions. Follow all 

    instructions, since incorrect installation can lead to 

    severe injury.

14. Before installing the drive, remove any unnecessary 

    cords and disable any equipment not needed for 

    powered operation.

Do not dispose of in general waste. 

Please recycle batteries and damaged electrical products appropriately.

-1-

-2-

Reviews: