eka KF 1010 UD, Use And Instruction Manual

Page: 12 / 20

_ TECNOEKA Srl __________________________________________________________ use and instruction manual _
_ page 12 _________________________________________________________________________________________
3.3 3.3 3.3 3.3 FFFFirst ignition irst ignition irst ignition irst ignition
When the oven is electrically powered for the first time, "ER2" appears on the control panel display
accompanied by a brief acoustic "
BEEP
".
This way the oven warns the user that the “heart” probe (“needle” probe) is not connected to the
relevant socket (for specifically designed ovens), thus the temperature value cannot be regulated.
The message disappears when the “ON/OFF” button is pressed ON and the selected parameter value
(“zero”) appears (Led on next to the relevant symbol).
If the selector is turned to “0”, “OFF” appears on the display. If electrical power is constant, the oven
is turned on and off normally with the "ON/OFF" button.
3.4 3.4 3.4 3.4 O O O Operation mode peration mode peration mode peration mode
The cooking cycle can be run in “manual” or “programmed” mode.
Each cycle is made up of several cooking parameters: time/temperature/humidity/”heart”
temperature (for specifically designed ovens)/half motor speed/half power.
MANUAL MODE
To select cooking parameters, turn the selector to the selected parameter (see symbol). To set or
change the selected parameter value, rotate the regulator knob clockwise (to increase) or counter-
clockwise (to decrease).
The “time” parameter (symbol ) can be set from 0 hours and 1 minute to 9 hours and 59
minutes. If "INF" appears on the display this mean the timer is not set and the oven will operate
continuously until manually turned off by pressing the "ON/OFF" button.
The “temperature” parameter (symbol ) can be set from 50° C to 270° C.
The “humidity/steam” parameter (symbol ) can be set from 0 to 100%.
The “temperature at heart” parameter (symbol ) can be set from 0° C to 100° C (for specifically
designed ovens).
IIII
N ORDER FOR THE
N ORDER FOR THE N ORDER FOR THE
N ORDER FOR THE
“ “ “ “
TEMPERATURE AT HEART
TEMPERATURE AT HEART TEMPERATURE AT HEART
TEMPERATURE AT HEART
” ” ” ”
PARAMETER TO WORK PARAMETER TO WORK PARAMETER TO WORK PARAMETER TO WORK
,,,,
IT MUST BE SET
IT MUST BE SET IT MUST BE SET
IT MUST BE SET BEFORE THE COOKING
BEFORE THE COOKING BEFORE THE COOKING
BEFORE THE COOKING
CYCLE STAR
CYCLE STAR CYCLE STAR
CYCLE STARTS
TS TS
TS
,,,,
AND THEN
AND THEN AND THEN
AND THEN
,,,,
BEFORE YOU SET THE
BEFORE YOU SET THE BEFORE YOU SET THE
BEFORE YOU SET THE TEMPERATURE
TEMPERATURE TEMPERATURE
TEMPERATURE PARAMETER IN THE COO
PARAMETER IN THE COO PARAMETER IN THE COO
PARAMETER IN THE COOKING CHAMBER
KING CHAMBER KING CHAMBER
KING CHAMBER
....
The “half motor speed/half power” parameter (symbol ) can be turned on (“on” appears on
the display) or off (“off” appears on the display).
A A A A
T LEAST COOKING TIME T LEAST COOKING TIME T LEAST COOKING TIME T LEAST COOKING TIME AND TEMPERAT AND TEMPERAT AND TEMPERAT AND TEMPERATURE PARAMETERS MUST URE PARAMETERS MUST URE PARAMETERS MUST URE PARAMETERS MUST BE SET FOR THE COOKI BE SET FOR THE COOKI BE SET FOR THE COOKI BE SET FOR THE COOKING CYCLE TO START NG CYCLE TO START NG CYCLE TO START NG CYCLE TO START
....
3.5 3.5 3.5 3.5 C C C Cooking cycle ooking cycle ooking cycle ooking cycle ON/OFF ON/OFF ON/OFF ON/OFF
When the door is closed, the cooking cycle automatically starts 5 seconds after setting the two
parameters required for cooking (time/temperature).
The lights in the cooking chamber, the resistance and motors turn on.
When the set cooking cycle time has elapsed, the oven automatically turns off, the set parameter
values clear on the display and an acoustic signal sounds for 3 seconds. The oven readies for new
cooking cycle settings.
The cooking cycle can be stopped at any time by pressing the “ON/OFF” button “OFF”.
The display turns off and an acoustic signal sounds for 3 seconds.
3.6
3.6 3.6
3.6 D
D D
Displaying
isplaying isplaying
isplaying //// changing parameters with the cooking cycle
changing parameters with the cooking cycle changing parameters with the cooking cycle
changing parameters with the cooking cycle ON
ON ON
ON
When the cooking cycle is on, parameters can be displayed by turning the selector knob to the
relevant symbol.
Parameters can be changed by turning the regulator knob.
- “Time” parameter
The cooking cycle count down is displayed (blinking led on symbol ).
- “Temperature” parameter
The set value (fixed led on symbol ) is displayed for 3 seconds alternated by the value