einflatables Slip and Splash Installation And Setup Manual Download Page 9

SET-UP PROCEDURE CONTINUED ... 

Step 9. 

Last minute steps before inflating. 

• Insure that the ride is prepared to be inflated.

Top Tethering. 

Secure top tethers to 

sandbags by inserting tethers through 

connection point on sandbags. Tie 3 

knots to connection point on sandbag 

making sure that  tethers  are secure and 

will not come loose during operation. 

Locate your sandbags so that the top 

tethers will be at a 50 degree vertical 

angle. ( 6' to  12' from inflatable depend­

ing on the size of the unit.) 

Establish a NO WALK perimeter zone 
around sandbags. 

• Check the ride and surrounding area for overhead obstruction, debris or anything that might 

puncture or damage the ride.

• Check the inlet tube(s) to make sure the blower(s) is/are securely attached and that all zippers, 

water/air flaps  and outlet tubes are closed. 

• Check all stakes or sandbag  devices,  tie downs, clips or ropes. If the stakes or sandbags are 

located away  from  the  ride they  should be covered  (stakes) and a "no walk  zone" should be 

established. 

• Check electrical cords for defects and proper connections. Make sure all electric cords and 

receptacles are the proper gauge and amperage. Electric cords should have some type of  stress 

relief  or guarding to prevent them from becoming unplugged. 

• Check the blower for proper guards, shields, size (hp)  and volume (cfm). Make sure everyone is 

clear  of the ride. 

• Check weather conditions to make sure the ride can inflated safely. Consult the 

Supplement 

Manual 

for specific limitations.

• When the unit is fully inflated check the inside & outside of the ride for rips and tears as well as 

signs of  aging and cracking.

• Check all netting for holes or rips.

• Check all blower tubes to make sure they are not kinked, twisted or partially obstructed.

• Check all tie down tethers for twists, tears, kinks and tension that could damage them or 

prevent them  from functioning properly.

IMPORTANT: Make sure that people or animals do not walk on the flat structure before inflation 

is 

attempted. This may damage your unit. Make sure no one is on the unit while unit is inflating 

or serious  injury may occur. All spectators should be at 

safe distance before you turn on blower. 

12405 Telegraph Road, Santa Fe Springs, CA 90670  Toll Free (800) 569-0719  •  (562) 777-1140  •  Fax (562) 777-1161 

10 

www.einflatables.com 

email: [email protected] 

Summary of Contents for Slip and Splash























Reviews: