Eiki LC-WB200 Owner'S Manual Download

Page: 54 / 80

Setting

Remote control

This projector provides two different remote

control codes: the factory-set initial code (

Code 1

)

and the secondary code (

Code 2

). This switching

function prevents remote control interference

when operating several projectors or video

equipment at the same time.

When operating the projector in

Code 2

, both the

projector and the remote control must be switched

Code 2

To change the code for the projector:

Select either

Code 1

Code 2

in this Setting

Menu.

To change the code for the remote control:

Press and hold both the MENU and IMAGE

buttons together for 5 seconds or more. After

changing the code, make sure the remote control

operates properly.



Note:

• When different codes are set on the projector and on the remote control, any operation cannot be made. In that

case, switch the code on the remote control to fit the code on the projector.

• If the batteries are removed from the remote control for a long period of time, the remote control code will be

reset.

Remote control

This function allows you to change brightness of

the screen.

Lamp control



Note:

• Lamp control can not be changed for a while after turning on the projector. Lamp needs some time to stabilize after

the power is turned on. Stored lamp mode will be active after the lamp is stabilized.

• If Mode 2 has been selected and the projection lamp exceeds the recommended total hours of use, the

replacement icon will be displayed at the time of power-on. Then the projector will turn off after 3 minutes.

•

The Lamp replacement icon will not appear when the Display function is set to

Off

(p.46), during

Freeze

(p.25), or

No show

(p.26).

Lamp control

Lamp life control

Select the lamp operation when the total lighting

time of a lamp exceeds the recommended total

hours of use.

Mode 1 . . . . . . . .

The lamp can be turned on even

after exceeding the recommended

total hours of use.

Mode 2 . . . . . . . . .

The lamp can be turned on even

after exceeding the recommended

total hours of use. But the projector

turns off automatically after 3

minutes.

Lamp replacement icon

Lamo control

Auto

.......Brightness according to the input

signal.

Normal

..Normal brightness

Eco 1

.....70%-80% of the normal brightness.

Eco 2

.....50% of the normal brightness.

Summary of Contents for LC-WB200

















































































Search results

Summary of Contents for LC-WB200

Reviews:

Related manuals for LC-WB200

Brands by name

Popular brands

Eiki LC-WB200, Owner'S Manual

Search results

Summary of Contents for LC-WB200

Reviews:

Related manuals for LC-WB200

Brands by name

Popular brands