Draper Ultimate Access E Instructions Installation & Operation Download Page 1

Page: 1 / 7

Overview -

Components

Contents

Overview -

Components ...............................................................................................1

Section 1 -

Removing Shipping Brackets

(Tab-Tensioned, "V" Surfaces only)

..............2

PLEASE READ -

Safety Information ............................................................................2

Section 2 -

Hanging Screen .........................................................................................3

Section 3 -

Bottom Access Panel/Trap Door Opening and Closing .....................3

Section 4 -

Motorized Roller/Fabric Installation ......................................................4

Section 5 -

Motorized Roller/Fabric Removal ..........................................................4

Section 6 -

Operation ...................................................................................................5

Section 7 -

Tab-Tension Adjustment Procedure ......................................................5

Section 8 -

Electrical Connections ............................................................................5

Section 9 -

Limit Adjustments .....................................................................................5

Section 10 -

Case Length Dimensions .......................................................................6

Section 11 -

Case Width Dimensions .........................................................................6

Section 12 -

Mounting Bracket Dimensions .............................................................6

Section 13 -

Wiring Diagrams: 220V Standard Motor .............................................7

CAUTION

Read and understand all warnings

(page 2)

before beginning installation.

Shipping Brackets Attached
to Dowel and Screen Case

(V Screens Only)

Please Note:

Shipping brackets must remain in place

until product has been mounted and connected to

power

(see Sections 1 and 4 in this document.)

Also, DO NOT operate screen before removing

shipping brackets from screen case.

TOOLS REQUIRED

POWER DRILL

PENCIL

TAPE MEASURE

HARDWARE

(by others)

LEVEL

“E” Free Hanging

Viewing Surface

“V” Flexible Vinyl

Viewing Surface

Mounting Bracket

Hoisting Bracket

Trim Flange

"E" Dowel

"V" Dowel

Leveling Bracket

Electrical Cutout

Tab Tensioning

Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385

draperinc.com | 765.987.7999 | 800.238.7999

FORM: UltimateAccess220V_Inst20

Ultimate Access E and V 220V

Electric Projection Screen

INSTRUCTIONS

INSTALLATION & OPERATION

If you have any difficulties installing or servicing your

Ultimate Access screen, call your dealer or Draper, Inc.

Summary of Contents for Ultimate Access E








Search results

Summary of Contents for Ultimate Access E

Reviews:

Related manuals for Ultimate Access E

Brands by name

Popular brands

Draper Ultimate Access E, Instructions Installation & Operation

Search results

Summary of Contents for Ultimate Access E

Reviews:

Related manuals for Ultimate Access E

Brands by name

Popular brands