background image

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

  When using electrical appliances, safety precautions to reduce the risk 

of fire, electric shock or injury to persons should be followed, including:

1. 

READ ALL INSTRUCTIONS BEFORE USING THIS WATER HEATER.

2. 

This water heater must be grounded. Connect only to properly grounded outlet.  

 

See “GROUNDING INSTRUCTIONS” found on page 10.

3. 

Install or locate this water heater only in accordance with the provided 

 

installation instructions.

4. 

Use this water heater only for its intended use as described in this manual.

5. 

Do not use an extension cord set with this water heater. If no receptacle is  

 

available adjacent to the water heater, contact a qualified electrician to have 

 

one properly installed.

6. 

As with any appliance, close supervision is necessary when used by children.

7. 

Do not operate this water heater if it has a damaged cord or plug, if it is not 

 

working properly, or if it has been damaged or dropped.

8. 

This water heater should be serviced only by qualified service personnel.  

 

Contact nearest authorized service facility for examination, repair, or adjustment.

SAVE THESE INSTRUCTIONS

The manufacturer and/or distributor is not responsible for damages caused by 

improper installation, or by non observance of the instructions in this manual.

A QUALIFIED, LICENSED TECHNICIAN MUST ALWAYS INSTALL THE WATER HEATER 

AND CONDUCT ALL SUBSEQUENT SERVICE WORK AND/OR MAINTENANCE.

IMPORTANT!!!

NEVER TURN THE WATER HEATER POWER ON UNTIL THE TANK IS COMPLETELY FULL 

AND WATER IS FLOWING OUT OF THE HOT WATER FAUCET.

Page 2

Eemax mini tank manual.indd   3

5/30/2008   10:44:49 AM

Summary of Contents for EMT2.5





















Reviews: