background image

Using the seat level indicator

The level indicator is designed to help you install the car seat at 

the correct angle on the passenger seat.  It is located on the 

outside of the seat as indicated in Diagram 1. above.

When the seat is fitted to your vechicle, the level indictor bell 

should always fit inside it’s housing as indicated in Diagram 2 

above.

Adjust the child restraint to the proper level to ensure maximum 

protection for your child. A tightly rolled towel under the front 

edge of the car seat can be used to achieve the correct level.

IMPORTANT

 – always check the indicator before and after fitting 

your car’s seat belts.

10

designed & printed in NZ

1.

2.

Securing the harness to your child

1.  Place your child in the seat.  Make sure that your child’s back and 

bottom are flat against the seat.  This will maximise comfort and 

allow the harness to properly secure your child.

2.  Position the height of harness according to your child’s height. 

The harness straps should be level with their shoulders. 

IMPORTANT

 - Do not use the car seat with the harness if the 

child’s shoulders are above the highest slots in the backrest or 

if the child’s weight exceeds 13kg (to adjust the shoulder strap 

height see ‘Adjusting the shoulder belt height’).
As pictured in Diagram 1, combine the two locking clips together 

and insert them into the buckle housing until you hear a 

CLICK!.  

When it is connected it should appear as

 

pictured in Diagram 

2.  Check that the buckle is secure by pulling the buckle.  There 

should be a strong connection.
To tighten the shoulder straps, push the harness adjuster button 

at the front of the seat and pull the harness adjusting strap.  

3.  To loosen the shoulder straps, push the harness adjuster button 

and pull the two shoulder straps towards yourself.  

IMPORTANT

 - for proper tightness, one finger (1cm) should fit 

between the harness straps and the child’s shoulders.

4.  To open the harness, press the red buckle release button on the 

buckle.

11

designed & printed in NZ

1.

2.

Summary of Contents for Ed & Co FA005










Reviews: