Edwards & Co Ed & Co FA005 Instruction Manual Download Page 3

•  The car seat is not intended to be a substitute baby cot or bed. 

It is only designed to enable safe transportation of children in 

motor vehicles. 

NEVER

 leave a baby in the restraint for long 

periods of time.

•  Do not store in areas that may get hot, like in car boots, roof 

space or beside shed walls which can get hot in summer. 

NEVER

 

place heavy items on top of the seat as this may distort the 

plastic.

•  The restraint should not be purchased or sold as a second hand 

item unless you are sure about it’s history. 

•  Do not to use this car seat if it is older than 10 years from the 

manufacture date (stamped on the underside of the seat) as the 

protection in an accident may be reduced. 

•  When in use with a stroller, 

ENSURE 

the seat it fitted tightly.

•  The handle 

MUST 

be set in the correct position when used in the 

car or stroller. 

GENERAL WARNINGS

4

This is a “Universal” child restraint approved to European ECE 

R44/04 suitable from birth to 13 kg tested by TNO in the 

Netherlands.

“Universal” means the seat is approved for use in all vehicles that 

meet ECE R14 and R16 regulations.  A proper fit is more likely if 

your vehicle declares in it’s user manual that it is designed to fit a 

“Universal” child restraint.

Vehicles that are declared “Universal” have been done so 

under more stringent conditions than those applied to earlier 

designs which do not carry this notice.

If in doubt, please contact Edwards & Co or your retailer.

designed & printed in NZ

Features of your car seat

5

designed & printed in NZ

Summary of Contents for Ed & Co FA005










Reviews: