background image

 
 

WB12T 

 
 

 

 

6  S

AFETY

 

 

Warning 

 

Check the compatibility of the voltage and the frequency with the 

data on the rating plate prior to use. Repairs must be carried out 

only by qualified personnel

 

 

6.1  Dangerousness of the wire saw WB12T 

 

The wire saw system wb12T is equipped with protection devices, however, there is danger 
when  operating  it  faultily  or  misuse  it.    All  persons  that  are  concerned  with  the  set-up,  the 
initial  operation,  the  handling  and  maintenance  of  the  system,  have  to  carefully  read  and 
adhere to the following notes.  

 

6.2  Intended use  

 

The  wire  saw  wb12T  is  built  state-of-the-art.  If  the  machine  is  used  in  an  other  than  the 
intended way, it is dangerous for the user. 
 

  The system is suitable only for wire saw works, using wire saws up to Ø 12 mm.  

  Without the drive unit protective cover (Pict. 2 pos. 1) see p. 16

no cut may be done.  

  If  the  air  is  affected  by  the  cutting  process,  provide  fresh  air  for  the  user  for  his 

protection (mainly when dry cutting).  

  Spare  wire  lengtsh  can  be  covered  by  safety  guards.  However,  staying  in  the 

direction  of  the  alignment  or  in  the  danger  area  (

Pict.  3

,  see  page  16)

 

during 

operation is strictly forbidden.  

  All used wires must be approved for a cutting speed of 30 m/sec.  

  Wires may only be used if the following data is known: 

o

  Applicability of use (concrete, masonry, steel, cast iron etc.) 

o

  Dimensions 

o

  Allowed cutting speed 

o

 

Allowed wire connector (preferent. EDT EURODIMA bwc9 quick wire connector)

  

  Chapped or deformed wires may not be used.  

  Prior  to  every  use,  the  diamond  wire  and  the  wire  connector  must  be  checked  for 

damages. When defect, the wire resp. the wire connector must be renewed.  

  Dry and wet cut: The wire saw system wb12 is designed for both dry and wet cuts.  

 

 

Caution high-voltage current!  

Danger to life

, when lines are cut or defect!  

 
All  system  use  beyond  is  classified  as  not  complying  with  the  regulations.  For  damages 
resulting from this misuse, the manufacturer cannot be held liable. The risk is borne by the 
user himself.   

Summary of Contents for Braxx WB12T

























Reviews: