background image

1. HOT FILM

 10. After checking the status of lamination, Place the pressure lever at the proper
   lamination mode.

 6. Allow some of the film with melted resin to stick to the Guiding Paper.
 7. Repeat step 5 with lower roll film then stick it to the Guiding Paper.

   fed through to the rear roller without tension.

 8. Unwind 30~40cm(1~1.3ft) of both rolls of film, to loosen the film tension. This should be

 1. Insert the bar into the core of roll film then place the bar on the machine.

HANGING   FILM

   beyond the second set of rollers.

 9. Set speed at 1 and press the "RUN" button to feed film into the machine.

 2. Place the Pressure Lever to the open mode (10~13mm).
 3. Insert a piece of lightweight cardboard (Guiding Paper) between the rollers, through to

      **IMPORTANT

 : It should reach beyond the second set of rollers. It should stick out

                              5cm (2") in front of front roller.
 4. Pull the upper film around the upper idler bar to the anti-wrinkle device and stretch out
   the film on the upper heat shoe.
 5. When the temperature reaches 80°C (176°F), the resin is melting, stick the film on the
   shoe.  

SHAFT

LOWER IDLE BAR

UPPER ROLL FILM

SHAFT

LOWER ROLL FILM

GUIDING PAPER

HEAT SHOE

UPPER IDLE BAR

LOWER FILM

SHAFT

LOWER IDLE BAR

HEAT SHOE

Picture 1

 

- 8 -

EDNord - Istedgade 37A - 9000 AAlborg - telefon 96333500 

Summary of Contents for RSS-1050




























Reviews: