EDNord magicolor 2500W User Manual Download Page 91

Page: 91 / 108

Solving Other Problems

Media is
wrinkled.

The media is moist
from humidity or hav-
ing water spilled on it.

Remove the moist media and replace it
with new, dry media.

The media feed roller
or fuser unit is defec-
tive.

Check them for damage. If necessary,
contact Technical Support with the
error information.

Unsupported media
(wrong size, thick-
ness, type, etc.) is
being used.

Use KONICA MINOLTA-approved
media. See “Media Specifications” on
page 24 for supported sizes and types.
For a complete list of approved media,
go to www.printer.konicaminolta.com.

Envelopes are being
printed with the fuser
separator levers in
the plain paper posi-
tion.

Before printing envelopes, place the
fuser separator levers in the envelope
position.

Symptom

Cause

Solution

EDNord - Istedgade 37A - 9000 AAlborg - telefon 96333500

Summary of Contents for magicolor 2500W













































































































Search results

Summary of Contents for magicolor 2500W

Reviews:

Related manuals for magicolor 2500W

Brands by name

Popular brands

EDNord magicolor 2500W, User Manual

Search results

Summary of Contents for magicolor 2500W

Reviews:

Related manuals for magicolor 2500W

Brands by name

Popular brands