EDNord magicolor 2500W User Manual Download Page 67

Page: 67 / 108

Maintaining the Printer

Do not leave the printer’s covers open for any length of time, especially in
well-lit places; light may damage the drum cartridge.

Do not open the printer during printing.

Do not tap media stacks on the printer.

Do not lubricate or disassemble the printer.

Do not tilt the printer.

Do not touch the electrical contacts, gears, or laser devices. Doing so
may damage the printer and cause the print quality to deteriorate.

Keep media in the output tray at a minimum level. If the media is stocked
too high, your printer may experience media misfeeds and excessive
media curl.

Keep the printer level to avoid
toner spillage.

When lifting the printer, grasp
the areas shown in the figure.

If you get toner on your skin,
wash it off with cool water and a mild soap.

CAUTION

If you get toner in your eyes, wash it out immediately with cool water
and consult a doctor.

Make sure any parts removed during cleaning are replaced before you
plug in the printer.

EDNord - Istedgade 37A - 9000 AAlborg - telefon 96333500

Summary of Contents for magicolor 2500W













































































































Search results

Summary of Contents for magicolor 2500W

Reviews:

Related manuals for magicolor 2500W

Brands by name

Popular brands

EDNord magicolor 2500W, User Manual

Search results

Summary of Contents for magicolor 2500W

Reviews:

Related manuals for magicolor 2500W

Brands by name

Popular brands