background image

General Notes

 

 
 
Dear customer, 
 
Thank you for choosing a 

Bühler 

high-quality product for supporting you in your work. 

 
The 

Bühler 

shakers were developed for the use in laboratories. 

 
If you pay attention to the following points, the device will reward you with long life and 
optimal operation. 
 
 
 

1) Read the operating instructions carefully before initial operation. 
 
2) The user must acquaint himself with the safety instructions and operating 

conditions in order to avoid damage / injuries to material and personnel. 

  
3) Liability and all claims under warranty end immediately in case of damages 

which result from misuse and / or abuse. 

 
4) The devices were carefully checked for perfect functioning and condition before 

delivery. 

 
5) Necessary servicing or repair work may only be done by personnel of the 

Edmund Bühler GmbH 

technical service department, their authorized agents or 

personnel trained by 

Edmund Bühler GmbH

 
6) For shipping, the device must be adequately and safely packed. If possible, use 

the original packing. 

 
7) If the device is returned to 

Edmund Bühler

 for repair, it should be cleaned and 

free of any harmful substances or residues.  

 
These operating instructions are protected by copyright. 

Edmund Bühler GmbH   ALLGEM\BED.SMG/BEDSME/TXTE.DOC – 01/08 

3

Summary of Contents for KS 15 control























Reviews: