background image

 

Quick Installation Guide 

 

OAP100  Access  Point 

ENGLISH 

 

iv 

 

  Radio 

-

 

EN 300 328 V2.1.1 (2.4G/BT-LE) 

-

 

EN 301 893 V2.1.1 (5G) 

-

 

EN 301 908-1 V11.1.1 (LTE) 

-

 

EN 303 413 V1.1.1 (GPS) 

-

 

EN 50385 / EN 62311: 2017 (MPE) 

  EMC 

-

 

EN 301 489-1 V2.1.1 

-

 

EN 301 489-17 V3.1.1 

-

 

EN 301 489-52 V1.1.0 

  Safety:   

-

 

EN 60950-1: 2006 + A11: 2009 + A12: 2011 + A2: 2013 

-

 

EN 60950-22: 2017 

-

 

IEC 62368-1: 2014 (Second Edition) 

-

 

IEC 60529: 1989+AMD1: 1999+ AMD2: 2013CSV (IP55)

 

Caution   

 

This  declaration  is  only  valid  for  configurations  (combinations  of  software,  firmware,  and  hardware) 

provided  and  supported  by  Edgecore  Networks  Corporation.  The  use  of  software  or  firmware  not 

provided and supported by Edgecore Networks Corporation. may result in the equipment no longer being 

compliant with the regulatory requirements. 

  Requirements in 

AT/BE/BG/CZ/DK/EE/FR/DE/IS/IE/IT/EL/ES/CY/LV/LI/LT/LU/HU/MT/NL/NO/PL/PT/RO/SI/SK/TR/FI/SE 

/CH/UK/HR. 

  In  order  to  ensure  compliance  with  the  exposure  recommendations  to  electromagnetic  fields,  the  device 

should be used at a minimum distance of 20cm from the body.

 

 

 

Taiwan NCC Statement 

 

 

根據 NCC 低功率電波輻射性電機管理辦法  規定:

 

第十二條

 

經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或

變更原設計之特性及功能。

 

第十四條

 

 

 

低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善
至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機須忍受
合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

 

  

減少電磁波影響,請妥適使用

Summary of Contents for OAP100
















Reviews: