background image

 

Quick Installation Guide 

 

OAP100  Access  Point 

ENGLISH 

 

ii 

FCC CAUTION 

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class  B  digital  device, 

pursuant  to  Part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable  protection 

against  harmful  interference  in  a  residential  installation.  This  equipment  generates,  uses  and  can 

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may 

cause  harmful  interference  to  radio  communications.  However,  there  is  no  guarantee  that 

interference  will  not  occur  in  a  particular  installation.  If  this  equipment  does  cause  harmful 

interference to radio or television reception, which can be determined by turning the equipment off 

and  on,  the  user  is  encouraged  to  try  to  correct  the  interference  by  one  or  more  of  the  following 

measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the  receiver  is 

connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) 

This device may not cause harmful interference, and (2) this device must accept any interference received, 

including interference that may cause undesired operation. 

 

47 CFR FCC Part 15, Subpart B, Class B 

47 CFR FCC Part 15.247 (2.4G/BT-LTE) 

47 CFR FCC Part 15.407 (5G) 

 

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance 

could void the user's authority to operate this equipment. 

 

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 

 

Radiation Exposure Statement

 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This 

equipment  should  be  installed  and  operated  with  minimum

  distance  129  cm  between  the  radiator  &  your 

body. 

 

 

For  product  available  in  the  USA/Canada  market,  only  channel  1~11  can  be  operated.  Selection  of  other 

channels is not possible. 

Summary of Contents for OAP100
















Reviews: