Edge-Core ES4704BD User Manual Download Page 66 | Manualshive

Page: 66 / 93

Edge-Core ES4704BD User Manual Download Page 66

56

Step 2: Put the hanger-mounted switch smoothly into a standard 6’’ rack.

Because of the size and weight of a ES4700BD, 2 people are required to complete

the installation. With a person standing on each side of the chassis, grasp
the chassis handle in the lower side panel with one hand, and use the other
hand near the top of the chassis for balance. Slowly lift the chassis in unison
and carry it to the rack. Lift the ES4700BD to a position a little higher than
the mounting shelf or sliding rails, resting the chassis on the shelf/rails, and
then carefully slide the chassis into the rack. Be sure to align the hangers
and mounting holes in the rack column.

Step 3: Fasten the ES4700BD to the rack with the screws provided.

Bolt the hangers to the matching holes in the rack column with the screws
provided. Be sure to tighten the screws smoothly. The ES4700BD should
now be securely attached to the equipment rack.

The procedure is shown below:

Fig 2-3 Rack-mounting ES4704BD

«
...
64
65
66
67
68
...
»

Summary of Contents for ES4704BD






























































































Reviews:

No comments