Eddyfi Technologies INUKTUN VERSATRAX 100, User Manual, Page: 21 / 41

Share

Page: 21 / 41

Eddyfi Technologies INUKTUN VERSATRAX 100 User Manual Download Page 21

Versatrax 100™

Document: UMDT013103.docm

Revision: A10

Created by: KJB

Date: 26 Sep 2019

3070984-A10

Source Location: C:\ePDM\ISLEng\products\dt-versatrax100mkii\manuals\UMDT013103.docm

Page 21 of 41

Us

er

M

an

u

al

Track Removal/ Installation

The Microtracs

™ are removed or installed onto the vehicle using four M5x8mm socket cap screws. The

track whip connector must be fully mated (finger tight only), and the whip secured on place on the chassis
using the provided P-clips.

FIGURE 12: PARALLEL TRACK REMOVAL

The VT100

™ crawler is intended for 70V operation.

This vehicle should only be fitted with Microtracs

marked for 70V DC supply.

48V rated tracks will be damaged if connected to this system.

Warning: Track Voltage Input

– Microtracs are supplied in two different voltage ranges: 36-

48VDC, and 30-70 VDC. Verify your tracks have the correct voltage input range for your
system. 48V rated tracks will be damaged if connected to a 70-Volt system. Wide input tracks
are designated by a

\V/

symbol on the side plate.

«
...
19
20
21
22
23
...
»

Summary of Contents for INUKTUN VERSATRAX 100










































Reviews:

No comments