manualshive.com logo in svg

ECS 761GXM-M2, Manual, Page: 50 / 58

Share
Download
ECS 761GXM-M2 Manual Download Page 50

44

44

4

JBOD:

 (Just a Bunch of Drives). Also known as “Spanning”. Two or

more hard drives are required. Several hard disk types configured as
a single hard disk. The hard drives are simply hooked up in series. This
expands the capacity of your drive and results in a useable total ca-
pacity. However, JBOD will not increase any performance or data
security.

Installing Software Drivers

SiS provides RAID driver for SiS965L SATA with RAID function.

1

For RAID function, SiS965L support RAID0, RAID1 and JBOD by soft-

ware RAID driver only.

2

Support the function of installing windows to RAID array.

New Windows 2000/XP Installation

1

Start the installation:
Boot from the CD-ROM. Press F6 when the message “Press 

F6 

key if

you need to install third party SCSI or RAID driver” appears.

2

When the Windows 2000/XP Setup window is generated, press 

S 

key

to specify an Additional Device(s).

3

Insert the  driver diskette into drive A: and press Enter.

4

Choose one of the following items:

“WinXP SiS Raid/IDE Controller”

,

“Win2000 SiS Raid/IDE Controller”

,

that appears on screen, and then press the Enter key.

5

Press Enter to continue with installation or if you need to specify any

additional devices to be installed, do so at this time. Once all devices
are specified, Press Enter to continue with installation.

6

From the Windows 2000/XP Setup screen, press the Enter key. Setup

will now load all device files and then continue the Windows
2000/XP installation.

7

Please install the driver package again (ex. SiS RAID driver v1.00)

while the operation system has been setup.

Existing Windows 2000/XP/98/Me Installation

1

Install the driver by executing SiS driver setup utility.

2

The drivers will be automatically installed.

Confirming Windows 2000/XP Driver Installation

1

From Windows 2000/XP, open the Control Panel from “My Computer”

followed by the System icon.

2

Choose the “Hardware” tab, then click the “Device Manager” tab.

3

Click the “+” in front of “SCSI and RAID Controllers” hardware type. The

driver 

“SiS 180 Raid Controller”

 should appear.

If you would like to install windows to any RAID set, you should create RAID
from BIOS utility or SiS965L RAID Utility first and then follow the steps
above.

Summary of Contents for 761GXM-M2



























































Reviews:

No comments