ECR International Dunkirk DMG-240 Installation, Operation & Maintenance Manual Download

Page: 82 / 86

13 - TROUBLE SHOOTING

Troubleshooting Chart 11

Start Boiler.

Is supply line warmer than

return line?

YES

Assure wire harness

plugs are securely

connected to sensors

Replace Pump

E43

- No Water Temperature

Difference During Operation

Check wire plugs are

securely connected to

temperature sensors.

YES

Onboard pump operating

properly?

YES

Check both sensors

are properly inserted

into pipe lines.

YES

Possible air in the

system. De-aerate.

NOT OK

Done

Not OK

Repair Sensor

Insertion Into

Pipe Lines.

Refer to Temperature

Sensor Chart (both

sensors)

Replace Sensor

Replace Control

Board

PN 240011656 REV. K [11/01/2020]

Summary of Contents for Dunkirk DMG-240























































































Search results

Summary of Contents for Dunkirk DMG-240

Reviews:

Related manuals for Dunkirk DMG-240

Brands by name

Popular brands

ECR International Dunkirk DMG-240, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for Dunkirk DMG-240

Reviews:

Related manuals for Dunkirk DMG-240

Brands by name

Popular brands