background image

24

Warranty

ECOWATER

S Y S T E

M S

EcoWater Systems LLC

Advantage Warranty

Series ETF AIIF Water System

Congratulations! You have just purchased the highest quality water conditioning product on the market. To register your

warranty, complete the enclosed Warranty Registration Card and mail it within 30 days of purchase.
To whom is this warranty extended?
EcoWater Systems LLC warrants its products to the original owner and guarantees that the products will be free from de-

fects in materials and workmanship from the original date of installation.
How does my warranty work?
If, during the respective warranty period, a part proves, after inspection by EcoWater, to be defective, EcoWater will, at

its sole option repair or replace that part at no charge, other than normal shipping and installation charges.
What is covered by the warranty?
EcoWater systems LLC guarantees that,
for the LIFETIME of the original owner, the MINERAL TANK will not rust, corrode, leak, burst, or in any other manner fail

to perform their proper functions and that,
for a period of FIVE (5) YEARS after installation, the VALVE BODY will be free of defects in materials and workmanship

and will perform its proper function and that,
for a period of THREE (3) YEARS after installation, the ELECTRONIC FACEPLATE will be free of defects in materials and

workmanship and will perform its normal functions and that,
for a period of ONE (1) YEAR after installation, ALL OTHER PARTS will be free of defects in materials and workmanship

and will perform their normal functions.
How do I obtain local service?
Should you need service, your local, independent EcoWater Dealer is only a phone call away.

PHONE:

If I need a part replaced after the factory warranty expires, is that part warranted?

Yes, EcoWater Systems LLC warrants FACTORY REPAIRS as well as all replacement parts for a period of 90 DAYS.

Are any additional warranties available?

We are pleased to say, YES! EcoWater Systems LLC offers an EXTENDED, PARTS ONLY WARRANTY for the ELEC-

TRONICS portion of your product. This warranty is called the “Perfect Ten” and extends the three year warranty on the

electronic FACEPLATE, WIRING HARNESS, DRIVE MOTOR, TRANSFORMER, POWER CORD, SENSOR HOUSING,

and MICRO SWITCHES to a total of TEN YEARS from the date of original installation. Should your local dealer not offer

this warranty, you may contact the factory for additional information.*

General Provisions

The above warranties are effective provided the water conditioner is operated at water pressures not exceeding 125 psi,

and at water temperatures not exceeding 120

°

F; provided further that the water conditioner is not subject to abuse, mis-

use, alteration, neglect, freezing, accident or negligence; and provided further that the water conditioner is not damaged

as the result of any unusual force of nature such as, but not limited to, flood, hurricane, tornado or earthquake. EcoWater

Systems LLC, is excused if failure to perform its warranty obligations is the result of strikes, government regulation, materi-

als shortages, or other circumstances beyond its control.
To obtain warranty service, notice must be given, within thirty (30) days of the discovery of the defect, to your local EcoWa-

ter Systems dealer.
*THERE ARE NO WARRANTIES ON THE WATER CONDITIONER BEYOND THOSE SPECIFICALLY DESCRIBED

ABOVE. ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR OF FIT-

NESS FOR A PARTICULAR PURPOSE, ARE DISCLAIMED TO THE EXTENT THEY MIGHT EXTEND BEYOND THE

ABOVE PERIODS. THE SOLE OBLIGATION OF ECOWATER SYSTEMS LLC UNDER THESE WARRANTIES IS TO

REPLACE OR REPAIR THE COMPONENT OR PART WHICH PROVES TO BE DEFECTIVE WITHIN THE SPECIFIED

TIME PERIOD, AND ECOWATER IS NOT LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES. NO ECOWA-

TER DEALER, AGENT, REPRESENTATIVE, OR OTHER PERSON IS AUTHORIZED TO EXTEND OR EXPAND THE

WARRANTIES EXPRESSLY DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts or exclusions or limitations of incidental or con-

sequential damage, so the limitations and exclusions in this warranty may not apply to you. This warranty gives you specif-

ic legal rights, and you may have other rights which vary from state to state. This warranty applies to consumer--owned

installations only.

Summary of Contents for ETF AIIF115

























Reviews: