Eco Drive E5-H Series Manual Download

Page: 16 / 138

V&T Technologies Co., Ltd.

http://www.ecodrivecn.com

Chapter 2 Inverter Installation



Note:

When the E5

−

−4T7.5G and below power class inverters are mounted side by side in the cabinet,

please remove the upper dust guard and the lower leading board.

Fig. 2

−

2 Mounting direction and space for E5

−

−4T11G

and above power class

2.3 Removal and Mounting of Operation Panel and Cover

2.3.1 Removal and Mounting of Operation Panel



Removal of operation panel

As shown in Fig. 2

−

3, the grab on the operation panel forcefully in direction 1, and then lift the panel

body in direction 2.



Mounting of operation panel

As shown in Fig.2

−

4, align with the lower clamping position of the operation panel in direction 1,

and then press down the operation panel in direction 2, until the “crack” sound is heard.

Do not mount the operation panel in any other direction; otherwise, the operation panel will have

poor contact.

Above 100mm

Air circulation

position

Air circulation

position

Above 200mm

Air circulation position

Above 200mm

Air circulation position

Above 200mm

Summary of Contents for E5-H Series











































































































































Search results

Summary of Contents for E5-H Series

Reviews:

Related manuals for E5-H Series

Brands by name

Popular brands

Eco Drive E5-H Series, Manual

Search results

Summary of Contents for E5-H Series

Reviews:

Related manuals for E5-H Series

Brands by name

Popular brands