Echo SRM-266T Operator'S Manual Download Page 15 | Manualshive

Page: 15 / 40

background image

SRM-266T

OPERATION

© 10/2014 ECHO Inc.

X7502027204

15

To Advance Trimmer Line

See Maintenance Section for nylon line replacement.

Note: To advance trimmer line, tap trimmer head against the ground while the head is turning at normal

operating speed.

Remove Nylon Line Head

Note: Do not disassemble nylon line head.

1. Align locking hole in upper plate with notch in edge of gear

housing and insert head locking tool (D).

2. Remove line head (E) by turning it clockwise until head is

completely off of shaft.

3. Remove locking tool (D).

Support Handle Installation

Note: Label shows minimum spacing for support handle

location.

1. If necessary, position support handle for comfortable

operation and securely tighten screws.

OPERATION

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a complete stop before removing obstructions, clearing debris, or servicing unit.

Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause
unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit
so that exhaust is directed away from your face and body.

Operation of this equipment may create sparks that can start fires. This unit is equipped with a spark
arrestor to prevent discharge of hot particles from the engine. Metal cutters can also create sparks if
the cutter strikes rocks, metal, or other hard objects. Contact local fire authorities for laws or
regulations regarding fire prevention requirements.

D

E

MIN

SPACING

«
...
13
14
15
16
17
...
»

Summary of Contents for SRM-266T









































Reviews:

No comments

Related manuals for SRM-266T

Brand: Villager Pages: 108

Brand: Weed Eater Pages: 7

Brand: Echo Pages: 180

Brand: Echo Pages: 44

Brand: Gardena Pages: 11

Brand: Komatsu Pages: 36

Brand: Blaupunkt Pages: 16

Brand: Fieldmann Pages: 15

Brand: Nakayama Pages: 38

Brand: Leviton Pages: 4

Brand: Grizzly Pages: 100

Brand: GreenWorks Pro Pages: 40

UltraPower 60V ST60L03

Brand: GreenWorks Pro Pages: 32

Brand: Ryobi Pages: 34

Brand: McCulloch Pages: 13

Brand: Royal Pages: 32

Brand: Malmbergs Pages: 2

Brand: Bergman Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands