Echo SRM-266T Operator'S Manual Download Page 32

Page: 32 / 40

X7502027204

SPECIFICATIONS

SRM-266T

SPECIFICATIONS

This spark ignition system complies with the Canadian standard ICES-002.

MODEL

SRM-266T

Length w/o cutter head

1810 mm (71.3 in.)

Width

250 mm (9.85 in.)

Height

340 mm (13.4 in.)

Weight (dry) w/o cutter head

5.75 kg (12.8 lb.)

Engine Type

Air cooled, two-stroke, single cylinder gasoline engine

Bore

34.0 mm (1.34 in.)

Stroke

28.0 mm (1.10 in.)

Displacement

25.4cc (1.55 cu. in.)

Exhaust

Spark arrestor muffler or spark arrestor muffler with catalyst

Carburetor

Diaphragm w/purge pump

Ignition System

Flywheel magneto, capacitor discharge ignition type

Spark Plug

NGK BPMR-8Y (Gap 0.65 mm (0.026 in.)

Fuel

Mixed (Gasoline and Two-stroke Oil)

Fuel/Oil Ratio

50 : 1 Power Blend X

or ECHO Red Armor

ISO-L-EGD (ISO/CD 13738) and J.A.S.O.

M345- FD, two-stroke, air-cooled engine oil.

Gasoline

Use 89 Octane unleaded. Do not use fuel containing methyl alcohol, more than 10%
ethyl alcohol or 15% MTBE. Do not use alternative fuels such as E-15 or E-85.

Oil

Power Blend X

ECHO Red Armor

Premium Universal 2-Stroke Oil

Fuel Tank Capacity

0.50 lit. (16.9 US fl. oz.)

Starter System

Automatic Rewind Starter

Clutch

Centrifugal Type

Vibration Isolated System

Rubber cushion on engine mount (heavy duty). Rubber grip on front handle.

Operating Rod

25.0 mm aluminum Tube

Drive Shaft

6.35 mm (1/4 in.) flexible shaft

Gear Case Ratio

2.07:1 Reduction

Rotating Direction

Counter Clockwise; viewed from top

Cutter Head

Speed Feed® 450 LH Nylon line head, Line capacity 6 m (20 ft.)

Handle

Front - loop, Rear handle (w/o rubber)

Shoulder Harness

Optional

Idle Speed

2,900 RPM

Clutch Engagement Speed

3,900 RPM

Wide Open Throttle Speed (W.O.T.)

10,250 RPM

Summary of Contents for SRM-266T









































Search results

Summary of Contents for SRM-266T

Reviews:

Related manuals for SRM-266T

Brands by name

Popular brands

Echo SRM-266T, Operator'S Manual

Search results

Summary of Contents for SRM-266T

Reviews:

Related manuals for SRM-266T

Brands by name

Popular brands