background image

26

Do not store your unit for a prolonged period of time (30
days or longer) without performing protective storage
maintenance which includes the following:

1.

Store unit in a dry, dust free place, out of the reach of
children.

WARNING   

  DANGER

Do not store in enclosure where fuel fumes may
accumulate or reach an open flame or spark.

2.

Place the stop switch in the "OFF" position.

3.

Remove accumulation of grease, oil, dirt, and debris
from exterior of unit.

4.

Perform all periodic lubrication and services that are
required.

5.

Tighten all the screws and nuts.

S

TORAGE

Long Term Storage (over 30 days)

WARNING   

  DANGER

During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear
of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may
result.

6.

Drain the fuel tank completely and pull the recoil
starter handle several times to remove fuel from the
carburetor.

7.

Remove the spark plug and pour 7 cc (1/4 oz.) of
fresh, clean, two-stroke engine oil into the cylinder
through the spark plug hole.

A.

Place a clean cloth over the spark plug hole.

B.

Pull the recoil starter handle 2-3 times to
distribute the oil inside the engine.

C.

Observe the piston location through the spark
plug hole.  Pull the recoil starter handle slowly
until the piston reaches the top of its travel and
leave it there.

8.

Install the spark plug (do not connect ignition cable).

Summary of Contents for SRM-260 - 12-06





























Reviews: