background image

SHC-2620 / S

OPERATION

X7502342003

23

© 07/19 ECHO Incorporated

The blades must not move at idle, otherwise serious personal 
injury may result. Periodic carburetor adjustment may be 
necessary to assure blades do not move at idle. If blades move, 
readjust carburetor according to “Carburetor Adjustment” 
instructions in this manual or see your dealer.

6.

Throttle Trigger

After engine warm-up, grip the throttle handle and support handle. 
Depress the throttle trigger lockout, and gradually depress throttle trigger 
to increase engine RPM to operating speed.

Starting Warm Engine

The starting procedure is the same as Cold Start except DO NOT close the 
choke, and do not depress throttle trigger to wide open position.

The blades must not move at idle, otherwise serious personal 
injury may result. Periodic carburetor adjustment may be 
necessary to assure blades do not move at idle. If blades move, 
readjust carburetor according to “Carburetor Adjustment” 
instructions in this manual or see your dealer.

1.

Stop Switch

Move stop switch (A) away 
from the STOP position.

A

Summary of Contents for SHC-2620S













































Reviews: