background image

4

P/N 89031744530

• This unit can be dangerous and cause serious injury if improperly

used. To reduce injury risk to operator, helpers and bystanders, read
and understand the Operator's and Safety manuals.

• Blindness can occur from objects that are thrown or ricocheted even

with shield in place. Operators, helpers and bystanders must wear
ANSI Z87.1 approved eye protection.

• Always wear hearing protection when operating unit.
• Prevent accidental contact with unit and any cutting attachment.

Maintain a 15m (50 ft.) radius, DANGER ZONE surrounding the
operator. ONLY the operator, dressed in proper protective clothing
should be in the DANGER ZONE.

• DO NOT INSTALL METAL BLADES ON GT (GRASS TRIMMER)

MODELS.

• Cutting attachment does not stop immediately after releasingthrottle.

Keep hands and feet clear of blade/cutting attachment unless engine
is shut off and cutting attachment is not moving.

• Do not remove shields, modify the unit or install attachments or

parts not approved by ECHO.  Approved attachment information
and replacement Operator's and Safety Manuals are available from
your ECHO dealer or by writing: ECHO, INCORPORATED, 400
OAKWOOD RD., LAKE ZURICH, IL  60047.

WARNING  

  DANGER

INTERNATIONAL

 

SYMBOLS

Shaft Decal

WEAR HAND AND

FOOT PROTECTION

KEEP BYSTANDERS AND HELPERS

AWAY 15 M (50 FT.).

DO NOT USE

BLADES. STRING

LINE ONLY

DO NOT EXCEED

10,000 RPM.

DO NOT OPERATE

WITHOUT GUARDS

AND SHIELDS IN

PLACE.

BEWARE

-  THROWN,

RICOCHET

OBJECTS

SYMBOL

DESCRIPTION/APPLICATION

SYMBOL FORM/

SHAPE

SYMBOL

DESCRIPTION/APPLICATION

SYMBOL FORM/

SHAPE

HOT

SURFACE

CARBURETOR

ADJUSTMENT

- IDLE SPEED

CARBURETOR

ADJUSTMENT

- HIGH SPEED

MIXTURE

SYMBOL

DESCRIPTION/APPLICATION

SYMBOL FORM/

SHAPE

SYMBOL

DESCRIPTION/APPLICATION

SYMBOL FORM/

SHAPE

Read and understand

Operator's Manual.

WEAR EYES, EARS

AND HEAD

PROTECTION

EMERGENCY STOP

FUEL AND OIL

MIXTURE

FINGER SEVERING

CARBURETOR

ADJUSTMENT

- LOW SPEED MIXTURE

SAFETY/ALERT

DO NOT SMOKE

NEAR FUEL.

DO NOT ALLOW

FLAMES OR

SPARKS NEAR

FUEL.

WEAR SLIP
RESISTANT

FOOT WEAR.

IGNITION

ON/OFF

PRIMER

BULB

CHOKE CONTROL

"COLD START"

POSITION

(CHOKE CLOSED)

CHOKE CONTROL

"RUN"

POSITION

(CHOKE OPEN)

Summary of Contents for GT-200i





























Reviews: