0-10VDC Low Voltage RF Wall Dimmer
Cat. No. ZS057-ALZ, Ratings: 24VDC, 20mA
INSTALLATION INSTRUCTIONS
ENGLISH
DI-003-ZS057-02A
Before Installation
• Install into any single-gang device back box.
• Supports multi-gang installations.
• Requires Decora
®
faceplate, sold separately.
• Devices use 0-10VDC low voltage control wires which may be installed as Class 1 or Class 2.
IMPORTANT:
If installed as Class 2, all devices in the circuit must be Class 2 rated and this dimmer must be wired per instructions below.
0-10V Dimming Installation
For 0-10V control wiring: connect the VIOLET wire to the +0-10V line and the GRAY wire to the 0-10V COMMON using Class 1 or Class 2 wiring
PHWKRGVDVLQGLFDWHGLQWKHVHLQVWUXFWLRQVEDOODVW¿[WXUHGULYHULQVWUXFWLRQVRUEDOODVW¿[WXUHGULYHUODEHOPDUNLQJV2EVHUYHDOOUHTXLUHPHQWVRIDQ\
authority having jurisdiction with respect to wire type, sleeving, isolation methods, and the like. Separation must be provided if Class 2 circuit is installed
WRJHWKHUZLWK&ODVVUHIHUWR1(&FRGHIRUDOORZDEOHPHWKRGVDQGVSHFL¿FDWLRQV
NOTE THE FOLLOWING:
6LOLFRQHWXELQJVKRXOGEH157/8/&6$(7/UHFRJQL]HGRUHTXLYDOHQWWRSURYLGHPHFKDQLFDOVHSDUDWLRQHTXDOWR´LQDLU
• Connectors joining 0-10V control wires should be approved LISTED CONNECTORS.
• Wire connectors and wire tubing should be provided by the installation contractor.
WARNINGS
•
TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT
BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
• To be installed and/or used in accordance with appropriate electrical codes
and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
CAUTIONS
• Use this device with
copper or copper clad wire only.
• For indoor applications only.
• Save these instructions.
To release, push sides.
Line up and press in to attach.
WARNING
:
TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF
POWER at circuit breaker or fuse and test that power is off
before wiring!
1.
Strip wires 3/4 in. and connect as per wiring diagram. Ensure
ZLUHVDUH¿UPO\DWWDFKHGDQGWKHUHLVQRH[SRVHGFRSSHU
2.
Gently place the wires and your device into the wall box and attach
with screws provided.
4.
If desired, change switch color.
5.
Install Decora faceplate.
Same Class Wiring Installation Shown
White
Orange/Yellow
Black
Red
Ground
Blue
Green
Violet
Gray
Black
ZS057-ALZ
BACKBOX
PURPOSE
BLACK
RED
+24VDC
WHITE
BLACK
COMMON
BLUE
ORANGE/YELLOW
LOCAL SWITCH
GREEN
GREEN
GROUND
VIOLET
VIOLET
9',00,1*
GRAY
GRAY
&20021',00,1*
3.
5HVWRUHSRZHUDQGWHVW212))RSHUDWLRQ6WDWXVOLJKWVKRXOGEULHÀ\
ÀDVK*5((1ZKHQWKHWRSRUERWWRPSDGGOHLVSUHVVHG
Lighting
Load
Powerpack
OPP20-0D2
Zone A
Line
BLU
BLU (SIG)
RED (+V/+24V)
BLK (COM)
BLU/WHT (MANUAL ON)
ORG/YEL (LOCAL SW INPUT)
VIO
GRY
BLU
BLK
WHT
Low Voltage
Occupancy
Sensor
BLU
BLK
WHT
Lighting
Circuit
Line Feed
NEU
WEB
VERSION
