background image

6

Read and understand this owner’s manual before operating your 
generator. It will help you avoid accidents if you are familiar with your 
generator’s safe operation procedures.

WARNING

Generator exhaust contains carbon monoxide, a 
poisonous gas that can kill you. 

You CANNOT smell or see this gas.

•  Use the generator outdoors, away from open windows, vents, or 

doors that could allow the carbon monoxide gas to come indoors. 
Keep the generator at least 1 meter (3 feet) away from any 
structure or building during use.

•  NEVER use a generator indoors, including in homes, garages, 

basements, crawl spaces, and other enclosed or partially-
enclosed areas, even with ventilation. Opening doors and 
windows or using fans will not prevent carbon monoxide build-up 
in the home.

•  NEVER use a generator in enclosed or partially-enclosed 

spaces. Generators can produce high levels of carbon monoxide 
very quickly. When you use a portable generator, remember that 
you cannot smell or see carbon monoxide. Even if you can’t smell 
exhaust fumes, you may still be exposed to carbon monoxide. 

•  NEVER operate the generator in an explosive atmosphere, near 

combustible materials or where ventilation is not sufficient to carry 

away exhaust fumes. Exhaust fumes can cause serious injury or 
death. 

•  If you start to feel sick, dizzy, or weak while using a generator, get 

to fresh air RIGHT AWAY. DO NOT DELAY. The carbon monoxide 
from generators can rapidly lead to full incapacitation and death.

•  If you experience serious symptoms, seek medical attention 

immediately. Inform medical staff that carbon monoxide poisoning 

is suspected. If you experienced symptoms while indoors, have 

someone call the fire department to determine when it is safe 

tore-enter the building.

SAFETY

Summary of Contents for EGi-3600LN















































Reviews: