background image

2 INCH CHIPPER/SHREDDER

1

ENGLISH

Section

SAFETY

1.  Read and understand this owner’s manual. Be 

completely familiar with the controls and the proper 

use of this equipment.

2.  Familiarize yourself with all of the safety and operating 

decals on this equipment and on any of its attachments 

or accessories.

3.  Keep safety decals clean and legible.  Replace missing 

or illegible safety decals.

4.  Obtain and wear safety glasses and use hearing 

protection at all times when operating this machine.

5.  Avoid wearing loose fitted 

clothing.  Never operate this 

machine while wearing clothing 

with drawstrings that could 

wrap around or get caught in 

the machine.

6.  Do not operate this machine 

if you are under the influence 

of alcohol, medications, or substances that can affect 

your vision, balance or judgement.  Do not operate if 

tired or ill.  You must be in good health to operate this 

machine safely.

Under California Law and the laws of several other states, 

you are not permitted to operate an internal combustion 

engine using hydrocarbon 

fuels on any forest covered, 

brush covered or grass 

covered land or on land 

covered with grain, hay or 

other flammable agricultural 

crops, without an engine 

spark arrester in continuous 

effective working order.  

1

1.1  SAFETY ALERT

1.2  EMISSION INFORMATION

Indicates a potentially hazardous situation that, if not 

avoided, may result in minor or moderate injury.

CAUTION

WARNING

Indicates a potentially hazardous situation that, if 

not avoided, could result in death or serious injury.

Indicates an imminently hazardous situation that, if not 

avoided, will result in death or serious injury.

DANGER

1.3  BEFORE OPERATING

The engine on your power equipment, like most outdoor 

power equipment, is an internal combustion engine that 

burns gasoline or diesel fuel (hydrocarbons).  Therefore, 

your power equipment must be equipped with a spark 

arrester muffler in continuous effective working order.  The 

spark arrester must be attached to the engine exhaust 

system  in  such  a  manner  that  flames  or  heat  from  the 

system will not ignite flammable material.

Failure of the owner/operator of the equipment to comply 

with this regulation is a misdemeanor under California law 

and may also be a violation of other state and/or federal 

regulations, laws, ordinances, or codes.  Contact your 

local fire marshal or forest service for specific information 

about which regulations apply in your area.

The standard muffler installed on the engine is not equipped 

with a spark arrester.  One must be added before using 

this machine in an area where a spark arrester is required 

by law.  Contact the local authorities if these laws apply to 

you.  See your authorized engine dealer for spark arrester 

options. 

The Owner/Operator’s manual uses this symbol to alert 

you of potential hazards.  Whenever you see this symbol, 

read and obey the safety message that follows it.  Failure 

to obey the safety message could result in personal injury, 

death or property damage.

Summary of Contents for BEAR CAT SC2170






















Reviews: