background image

10

Product Support: 

Eccotemp.com/help-desk

            Shop Online:

 Eccotemp.com/products          

Store Locator:

 Eccotemp.com/locator

Phone:

 866-356-1992 | 

Email:

 [email protected]

Address: 

315 - A Industrial RD Summerville, SC 29483

FILLING THE WATER HEATER

CAUTION!: Before powering the water heater, be sure that the

system is completely filled with water and All AIR IS REMOVED.

 If Water pipes 

Before connecting the power, fill the tank and system with water and

check for leaks. To be sure that all air is out of the water system, open

the hot water faucets on your fixtures until constant water flows. Any air

remaining in the tank will cause the water heater element to fail.

filling the water heater:

1. Open the hot water faucet.

2. Open the cold water supply valve.

3. When continuous water flows out of the faucet, the tank is filled.

4. Close the hot water faucet.

5. Check entire system for leaks.

ELECTRICAL CONNECTIONS

To be certain that all of the air is out of the water heater, open the HOT

water faucet on your fixtures until constant water flows from them. If air

remains in the tank, the element will be damaged when the electric cord

is plugged in.

Connect the water heater to a GROUNDED OUTLET.

The water heater is fitted with a power cord that is intended to

plug into a grounded 110-120 V/AC receptacle. Adhere to all

pertinent State and local codes. Install the correct size circuit

breaker into the master panel. The Seisco EMT water heater was

manufactured and wired in accordance with UL requirements.

The water heater is equipped with an overheat limiting device

with a manual reset. Also known as the temperature high limit,

this device has been factory installed to interrupt the power

supply in the event of a thermostat failure.

THIS WATER HEATER IS DESIGNED FOR 110-120V

SERVICE - DO NOT CONNECT TO ANY OTHER VOLTAGE.

Failure to use proper voltage may result in personal injury and/or

property damage. If the supplied electrical power cord is either damaged

or not long enough, do NOT use an extension cord. Have a licensed

electrician replace the power cord.

Summary of Contents for EM-2.5



















Reviews: