5580 Series - Reflex™ LED Minibars provide a compact
yet powerful warning solution that offers the flexibility of
either permanent, magnet, or vacuum-magnet mounting.
All models feature 12-24 VDC operation and use LED
reflector technology to maximize light output, offering
multiple flash patterns including double, quad quint, rotate
and random. 5587 models have no lens optics, distribut
-
ing light directly from the LED reflectors while 5580 &
5585 models feature lenticular lens optics to provide more
diffused light dispersion.
920-0149-00 Rev. K
Page 1 of 12
Installation and Operation Instructions
5500 Series LED Minibars
Specifications:
Size: 5580X, 5580XX, 5585X, 5585XX, 5585XXX 15” x 9” x 2.5”
5587X, 5587XX, 5587XXX
5580X-MG, 5580XX-MG, 5585X-MG 15” x 9” x 3.0”
5585XX-MG, 5585XXX-MG, 5587X-MG,
5587XX-MG, 5587XXX-MG
5580X-VM, 5580XX-VM, 5585X-VM, 15” x 9” x 31”
5585XX-VM, 5585XXX-VM, 5587X-VM
5587XX-VM, 5587XXX-VM
Available colors: CA,CB,CC,CR,CG,CAC,CAB,CAR,CRA,CAG,CRB
Weight: Permanent mount
approx. 3.4 lbs.
Magnet Mount
approx. 4.0 lbs.
Vacuum-Magnet Mount
approx. 5.7 lbs.
Input Voltage: 12 to 24 VDC systems
Current Draw:
5580: 2.7 Amps Maximum
Maximum power consumption: 35 watts
5585: 5.1 Amps Maximum
Maximum power consumption: 66 watts
5587: 5.1 Amps Maximum
Maximum power consumption: 66 watts
Flash Rate:
See Flash Pattern Chart
Temp. Range: -30ºC to +50ºC
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to ensure
the safety of you and those you are seeking to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,
which can cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output performance of the
system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system without losing
eye contact with the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag deployment
area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death. Refer to the
vehicle owner’s manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable mounting location
ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people,
vehicles or other obstructions.
7. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal. Never take the right-
of-way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, driving against traffic, respond-
ing at a high rate of speed, or walking on or around traffic lanes.
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding
warning signal devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The manufacturer as-
sumes no liability for any loss resulting from the use of this warning device.
Do not install and/or operate this safety product unless you have read and understand the safety information
contained
Failure to install or use this product according to manufacturers recommendations may result in property damage, serious injury, and/or death to
those you are seeking to protect!
!
WARNING!
Installation & Mounting:
Important!
This unit is a safety device, and it must be
connected to its own separate, fused power point to assure
its continued operation should any other electrical accessory
fail.
Vacuum-Magnet Mount:
The Vacuum-Magnet Mount feature includes suction cups on the
bottom of the minibar, with a magnet inside of the suction cup, for a
secure, temporary mount. The minibar should be placed in the center
of the roof where the least amount of curvature occurs. Before install
-
ing, make sure the mounting surface is clean and there is no debris
on the bottom of the minibar or on the roof of the vehicle, which could
reduce the holding power of the suction cup and magnet. Place and
remove the minibar without sliding to avoid scratching the paint on
the vehicle. After placement, the minibar should adhere firmly to the
surface. If the unit slides or moves easily, a proper installation has not
been obtained. To release the vacuum, lift the tab to release the air
-
lock (see Figure 1). To protect the Vacuum-Magnet Mount assembly,
return minibar to the box when not in use.
Do not attempt to attach
the minibar to an ice-covered surface.
Carefully remove the Minibar and place it on a flat surface. Exam
-
ine the unit for transit damage, and locate all parts. If damage is
found, or parts are missing, contact the transit company or ECCO.
Do not use damaged or broken parts.
