background image

Page 15 of 20

To enable a secondary cruise, takedown, work and alley light flash function:

1. Power-up the lightbar and apply +power to one wire from Table 17 that will be changed to a secondary mode. Programming will not work if 

    more than one function is selected at a time.

2. Tap the BLK/RED wire to +power to cycle through the module options for that mode. Hold for longer than 4 seconds to return to the factory 

    default setting. See the tables below for details. The single color columns apply when the lightbar has only single color work/takedown and 

    alley lights. The multicolor column applies to when the lightbar has any multicolor work/takedown and/or  multicolor alley lights.

Secondary Takedown Light Flash Mode Modules

Order Single Color

Multicolor

1

Standard Function per Table 1

Standard Function per Table 1

2

Front Outboard

Front Outboard

3

Front Inboard

Front Inboard

4

Front Center

Front Inboard, Outboard

5

Front Inboard, Outboard

Front Outboard, Corners

6

Front Center, Outboard

Front Inboard, Corners

7

Front Center, Inboard

Front Inboard, Outboard, Corners

8

Front Center, Inboard, Outboard

9

Front Outboard, Corners

10

Front Inboard, Corners

11

Front Center, Corners

12

Front Inboard, Outboard, Corners

13

Front Center, Outboard, Corners

14

Front Center, Inboard, Corners

15

Front, Corners

TABLE 18

Secondary Work Light Mode Modules

Order Single Color

Multicolor

1

Standard Rear Cut Function

Standard Rear Cut Function

2

Right Front Corner  

Right Front Corner  

3

Right Rear Corner

Right Rear Corner  

4

Right Corners

Right Corners

5

Work, Rear Outboard 

Work, Rear Outboard 

6

Work, Rear Inboard 

Work, Rear Inboard 

7

Work, Rear Center 

Work, Rear Center 

8

Work, Rear Outboard, Rear Inboard 

Work, Rear Inboard, Rear Center

9

Work, Rear Inboard, Rear Center

Work, Rear Ends

10

Work, Rear

Work, Rear

11

Work, Rear Outboard, Rear Corners

Work, Rear Outboard, Rear Corners

12

Work, Rear Inboard, Rear Corners

Work, Rear Inboard, Rear Corners

13

Work, Rear Center, Rear Corners

Work, Rear Center, Rear Corners

14

Work, Rear Outboard, Rear Inboard, Rear Corners Work, Rear Inboard, Rear Center, Rear Corners 

15

Work, Rear Inboard, Rear Center, Rear Corners 

Work, Rear Ends, Corners

16

Work, All Rear, Rear Corners 

Work, All Rear, Rear Corners 

TABLE 19

Summary of Contents for 21 Series





















Reviews: