Ebyte E32 Series User Manual Download Page 6

Page: 6 / 24

SX1278 Wireless Module

E32 Series User Manual

2.2.3 Turn-off current

Model

Min

Typ

Max

Unit

Remarks

E32-TTL-100

µA

● The turn-off current means the current consumed when

CPU, RAM, Clock and some registers remain operating

while SoC is at very low power consumption status.

●

The turn-off current is always lower than the current

consumed when the power supply source of the whole

module is at no-load status.

E32-TTL-100S1

µA

E32-T100S2

µA

If the voltage is at maximum value for long time, the

module may be damaged;

● The power supply pin has certain surge-resistance ability,

but the potential pulse higher than the maximum power

2.2.5 Communication level

If the communication level is higher than the allowed

maximum value, the module may be damaged;

● Although the communication level can be switched with

various methods, the power consumption of the whole

module will be affected at great degree.

● Modules are compatible with some of the microcontrollers

at 5V communication level. They are too many to be listed

here. Please base on practical test or talk to us for more

2.3 RF parameters

2.3.1 Transmitting power

Due to the error of the materials, each LRC component

has ± 0.1% error, so error accumulation will occur since

multiple LRC components are used in the whole RF circuit,

and the transmitting currents will be different at different

modules;

●

The power consumption can be lowered by lowering the

transmitting power, but the efficiency of the internal PA will

be decreased by lowering transmitting power due to

various reasons;

●

The transmitting power will be lowered by lowering the

power supply voltage.

E32-TTL-500

26.8

27.0

28.0

dBm

E32-TTL-1W

29.5

30.0

30.5

dBm

E32-433T30S

29.5

30.0

30.5

dBm

Summary of Contents for E32 Series

























Search results

Summary of Contents for E32 Series

Reviews:

Related manuals for E32 Series

Brands by name

Popular brands

Ebyte E32 Series, User Manual

Search results

Summary of Contents for E32 Series

Reviews:

Related manuals for E32 Series

Brands by name

Popular brands