Ebyte E32 Series User Manual Download Page 24 | Manualshive

Page: 24 / 24

background image

SX1278 Wireless Module

E32 Series User Manual

Copyright ©2012–2017, Chengdu Ebyte Electronic Technology Co., Ltd.

24

/

24

9. FAQ

9.1 Communication range is too short

The communication distance will be affected when obstacle exists.

Data lose rate will be affected by temperature, humidity and co-channel interference.

The ground will absorb and reflect wireless radio wave, so the performance will be poor when testing near ground.

Sea water has great ability in absorbing wireless radio wave, so performance will be poor when testing near the sea.

The signal will be affected when the antenna is near metal object or put in a metal case.

Power register was set incorrectly, air data rate is set as too high (the higher the air data rate, the shorter the distance).

The power supply low voltage under room temperature is lower than 2.5V, the lower the voltage, the lower the transmitting power.

Due to antenna quality or poor matching between antenna and module.

9.2 Module is easy to damage

Please check the power supply source, ensure it is 2.0V~3.6V, voltage higher than 3.6V will damage the module.

Please check the stability of power source, the voltage cannot fluctuate too much.

Please make sure anti-static measure are taken when installing and using, high frequency devices have electrostatic susceptibility.

Please ensure the humidity is within limited range, some parts are sensitive to humidity.

Please avoid using modules under too high or too low temperature.

10. Important notes

All rights to interpret and modify this manual belong to Ebyte.

This manual will be updated based on the upgrade of firmware and hardware, please refer to the latest version.

Please refer to our website for new product information.

11. About us

Technical support:

[email protected]

Documents and RF Setting download link:

www.cdebyte.com/en/

Tel：+86-28-61399028

Fax：028-64146160

www.cdebyte.com/en/

Address：Innovation Center D347, 4# XI-XIN Road,Chengdu, Sichuan, China

«
...
22
23
24

Summary of Contents for E32 Series

























Reviews:

No comments

Related manuals for E32 Series

Brand: Pakedge Pages: 7

Brand: Pakedge Pages: 4

Brand: Ebyte Pages: 11

Brand: Planet Pages: 29

Brand: 4IPNET Pages: 194

Brand: WAGO Pages: 66

Brand: Bountiful Pages: 58

Brand: Linksys Pages: 25

Brand: Ruckus Wireless Pages: 58

Brand: D-Link Pages: 101

Brand: Innoband Pages: 83

Brand: Brookstone Pages: 22

Brand: Marley Pages: 25

Brand: ELTEX Pages: 65

Brand: ELTEX Pages: 147

Brand: Acoustic Research Pages: 6

Sport PRO AM66-L

Brand: honor Pages: 156

Brand: V-Moda Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands