Ebyte E32 Series User Manual Download Page 22

Page: 22 / 24

SX1278 Wireless Module

E32 Series User Manual

7. Parameter setting

Step

Operation

Description

Install Driver

Please install the USB adapter driver (CP2102).

Pull out the jumper

Pull the M0, M1 jumper out, 3.3V or 5V are available for jumper.

Connect to module

Connect the module with USB adapter.
Connect to the USB interface of PC.

Open serial port

Operate the parameter setting software, choose corresponding serial number and press the
“OpenPort” button.
Please choose other serial numbers until open successfully.

Interface

Press“Preset”button，the interface will be as below.
If failed, please check if the module is in mode 3, or if the driver has been installed.

Input parameter

Please adjust the parameter as your request according to the corresponding setting, then click
“SetParam” button, write the new parameter to the module.

Complete the oper

ation

Please operate the “Fifth step” if you need to reconfigure,
if the configuration is completed,
please click "ClosePort" and then take off the module.

Commands

Configuration

Parameter configuration is also available for MCU (in mode 3).

Summary of Contents for E32 Series

























Search results

Summary of Contents for E32 Series

Reviews:

Related manuals for E32 Series

Brands by name

Popular brands

Ebyte E32 Series, User Manual

Search results

Summary of Contents for E32 Series

Reviews:

Related manuals for E32 Series

Brands by name

Popular brands