Ebyte E32-433T33D Page 7 User Manual Download | Manualshive

Page: 7 / 21

background image

Chengdu Ebyte Electronic Technology Co., Ltd

E32-433T30D User Manual

Copyright ©2012–2019

，

Chengdu Ebyte Electronic Technology Co.,Ltd.

6

7

GND

Input

Ground

8

Fixed orifice

Fixed orifice

9

Fixed orifice

Fixed orifice

10

Fixed orifice

Fixed orifice

11

Fixed orifice

Fixed orifice

12

Fixed orifice

Fixed orifice

13

Fixed orifice

Fixed orifice

14

Fixed orifice

Fixed orifice

15

Fixed orifice

Fixed orifice

4 Connect to MCU

No.

Description

（

STM8L MCU

）

1

The UART module is TTL level.

2

For some MCU works at 5VDC, M00 M11 AUX should connect to IO port of MCU, RX to TXD of MCU, TX to

RXD of MCU.

3

TVS protection and capacitors need to be added outside the power supply (it is recommended to add a 22uF low

ESR electrolytic capacitor or tantalum capacitor)

4

The RF module is sensitive to pulsed static electricity. Do not hot-swap the module.

5

It is recommended to use a power supply above 10W (5V 2A)

«
...
5
6
7
8
9
...
»

Summary of Contents for E32-433T33D






















Reviews:

No comments

Related manuals for E32-433T33D

tm-g5240 - T-mobile Hotspot Wireless

Brand: T-Mobile Pages: 2

Brand: Fresh 'N Rebel Pages: 24

STEVAL-SPBT4ATV3

Brand: ST Pages: 9

NORA-W30 Series

Brand: u-blox Pages: 52

Brand: PRO-NETS Pages: 72

Brand: GROM Audio Pages: 4

Brand: ZyXEL Communications Pages: 2

Brand: Veho Pages: 15

Brand: Linksys Pages: 42

Brand: IgniteNet Pages: 10

Brand: ausdom Pages: 60

Brand: Broadcom Pages: 10

Instant Wireless WAP54G

Brand: Linksys Pages: 67

Brand: u-blox Pages: 64

SimpleLink CC3135MOD

Brand: Texas Instruments Pages: 69

LiteBeam 5AC LR

Brand: Ubiquiti Pages: 32

Brand: Franklin Pages: 20

Brand: SleepPhones Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands