16-10-2009 9 033000=15301
• By keeping the buttons for the existing remote control pressed for a shorter
period, there will be more memory space left for learning codes on the TAKE
6 remote control. This also diminishes the chance that the remote control
learns the wrong codes.
• Experiment with the distance between the remote controls if you have
problems learning the codes.
• Some remote controls do not have the infrared LED in the centre. Try
experimenting by slightly moving the remote controls (sideways or
up/down). Tube lighting and bright sunlight can affect the procedure.
• You can only learn the codes for one original remote control per mode,
e.g. the codes for your DVD remote control under the DVD button. With
some combi devices (e.g. a TV with built-in DVD player) you first have to
learn the TV functions in TV mode and then the DVD functions in DVD mode.
Learning the commands
1. Point your existing remote control at the TAKE 6 Remote (front
to front
).
Keep a distance of 2,5 cm between the remote controls.
2. Press the SETUP (8) button until the LED stays lit. Release the SETUP (8)
button.
3. Press the Mode button (TV, AUDIO, SAT, etc.) for the device you want to
learn. The LED will flash once.
4. Press the LEARN (20) button. The LED will flash once.
5. Press the button on the TAKE 6 remote you want to store the new
command under. The LED will blink once.
6. Depending on the type of remote control you have, you can use one of
two methods:
a. Press the button on the existing remote control you want to learn.
Keep this button pressed until the LED on the TAKE 6 Remote
extinguishes. If the LED does not extinguish, but starts flashing, you
need to use method B. (If youhave just tried method A and want to
try method B, first repeat step 5).
b. Press the button on the existing remote control you want to learn.
Keep this button pressed as long as you would when using the
original remote control.
7. Repeat steps 5 and 6 for every button you want to learn.
8. When you have finished learning the buttons, press SETUP (8)
Erasing the commands learned per mode to clear memory space
You can erase the commands learned and saved for each separate
function (TV, VCR, etc.):
1. Keep the SETUP (8) button pressed until the LED stays lit. Release the SETUP
(8) button.
2. Press the Mode button of your choice (TV, DVR, etc.). The LED will flash
once.
3. Press the LEARN (20) button twice.
4. Press SETUP (8). The LED will extinguish after a few seconds.
5. All commands learned and saved for the selected function have now
been erased.
4.6. Identifying codes found
If you don’t know the code (for example because you found the code by
autosearch) you can identify it as described below:
1. Press and hold
S
(8) until the LED indicator (2) lights steadily. Release
S
.
2. Press the mode key (4) for the equipment you want to identify (DVR, DVD,
STB, AUDIO or AUX). The LED blinks once.
3. Press again
S
. The LED blinks once.
4. To identify the first digit press each number button from
0 - 9
(14) until the
LED blinks. The number you pressed is the first digit of the code.
5. Press each number key from
0 - 9
as above to find the second digit.
6. Press each number key from
0 - 9
as above to find the third digit.
7. Press each number key from
0 - 9
as above to find the fourth digit. When
the fourth digit has been found the LED will go off.
4.7 Volume Control Punch Through
The TAKE 6 remote control allows you to select which Mode controls your
volume/mute buttons. The
volume buttons (5)
and Mute (3) can be set for
individual control by EACH device Mode or can be set for ALL device Modes
to punch-through volume control to one specific single device Mode. The
