background image

8

Instruction Book    

IB182923EN   September 2018   www.eaton.com

AMH-4.76-VR

+

VR-Series

 Replacement Circuit Breaker

SECTION 3:   RECEIVING, HANDLING, AND 
STORAGE

VR- circuit breakers are subjected to complete factory 

production tests and inspection before being packed. They are 

shipped in packages designed to provide maximum protection to the 

equipment during shipment and storage and at the same time to 

provide convenient handling. Accessories such as the maintenance 

tool, cell code plate, (if applicable) etc. are shipped with the breaker 

(Figure 3.1).

3.1   RECEIVING

Until the breaker is ready to be delivered to the switchgear site 

for installation, DO NOT remove it from the shipping crate. If the 

breaker is to be placed in storage, maximum protection can be 

obtained by keeping it in its crate.
Upon receipt of the equipment, inspect the crates for any signs of 

damage or rough handling. Open the crates carefully to avoid any 

damage to the contents. Use a nail puller rather than a crow bar 

when required.
When opening the crates, be careful that any loose items or 

hardware are not discarded with the packing material. Check the 

contents of each package against the packing list.
Examine the breaker for any signs of shipping damage such as 

broken, missing or loose hardware, damaged or deformed insulation 

and other components. File claims immediately with the carrier if 

damaged or loss is detected and notify the nearest Eaton’s Electrical 

Services & Systems office.

Tools and Accessories

Mainttnanct Tool / Manual Chargt Handlte:

  This tool is used 

to manually charge the closing spring. One maintenance tool is 

provided with each vacuum unit replacement breaker. (Style# 

94C9506G01)

Racking Handlte:   

The racking handle is used to drive the racking 

mechanism which moves the circuit breaker into and out of the cell. 

The original OEM racking handle will interface with the VR- 

replacement breaker racking mechanism and is therefore not 

provided as part of the vacuum replacement breaker. A replacement 

racking handle may be purchased directly from Eaton. (Style# 

5D11330G01)

3.2   HANDLING

m

 WARNING

DO NOT USE ANY LIFTING DEVICE AS A PLATFORM FOR PERFORMING 

MAINTENANCE, REPAIR OR ADJUSTMENT OF THE BREAKER OR FOR 

OPENING, CLOSING THE CONTACTS OR CHARGING THE SPRINGS. THE 

BREAKER MAY SLIP OR FALL CAUSING SEVERE PERSONAL INJURY. 

ALWAYS PERFORM MAINTENANCE, REPAIR AND ADJUSTMENTS ON A 

WORKBENCH CAPABLE OF SUPPORTING THE BREAKER TYPE. 

VR- breaker shipping containers are designed to be handled 

either by use of an overhead lifting device or by a fork lift truck. If 

containers must be skidded for any distance, it is preferable to use 

roller conveyors or individual pipe rollers.

Once a breaker has been inspected for shipping damage, it is best 

to return it to its original shipping crate until it is ready to be installed 

in the Metal-Clad Switchgear.

When the breaker is ready for installation, a lifting harness in 

conjunction with an overhead lift or portable floor lift can be used to 

move the breaker. If the breaker is to be lifted, position the lifting 

device over the breaker and insert the lifting harness hooks into the 

breaker side lifting points and secure (lifting straps should have at 

least a 1000lbs lift capacity over the approximate breaker weight). Be 

sure the hooks are firmly attached before lifting the breaker. Stand a 

safe distance away from the breaker while lifting and moving.

Figurt 3.1.a. Typical Manual Chargt Handlt

Figurt 3.1.b. Rotary Racking Handlt

Figurt 3.2. Lifting AMH-4.76-VR+ 

Summary of Contents for VR+ Series



































Reviews: