Eaton RTX-12510 Service Manual Download

Page: 46 / 126

IV. Auxiliary Section -

RT-1110

Series

Removal and Disassembly of the Range Shift Cylinder Assembly

1. For ease of disassemble y, mount the auxiliary section

upright in a vise. Turn out the capscrews and remove the

range shift cylinder cover.

2. Turn the nut from the end of the shift yoke bar.

3. Cut the lockwire and turn out the two yoke lockscrews.

4. Pull the yoke bar to the rear and out of the cylinder.

Remove the piston from the housing.

5. Remove the O-rings from the OD and ID of the piston.

6. Turn out the capscrews and remove the shift cylinder

housing from the auxiliary plate. Remove the shift yoke
from the sliding clutch gear of the synchronizer assem-
bly. If necessary, remove the O-ring from the bore in the
cylinder housing.

Summary of Contents for RTX-12510































































































































Search results

Summary of Contents for RTX-12510

Reviews:

Related manuals for RTX-12510

Brands by name

Popular brands

Eaton RTX-12510, Service Manual

Search results

Summary of Contents for RTX-12510

Reviews:

Related manuals for RTX-12510

Brands by name

Popular brands