Eaton RTX-12510 Service Manual Download Page 124

Page: 124 / 126

Tool Reference

A few special tools are required in the disassembly and re-

assembly of Fuller transmissions. Although in many instances

basic mechanic's tools may be substituted with adequate re-

sults, it is highly recommended that the special tools be

made or purchased and used to ensure proper results and

avoid possible damage to the parts being installed or removed.

Fuller does not make or sell the tools listed, but tool

prints and catalogs of known manufacturers of ready made
tools are available upon request. Please mention tool print

number and model of transmission when ordering. Write:

Service Department / Eaton Corporation / Transmission

Division / 222 Mosel Avenue/ Kalamazoo, Michigan 49007

AUXILIARY PLATE HANGER BRACKET

Print Number T-22823

Used to support the auxiliary plate during removal and in-

stallation on the front case.

IMPACT PULLER Make from 18" steel rod threaded 1/2-13

on one end, attach end block and sliding block.

Used to remove reverse idler shafts.

OIL SEAL DRIVER Print Number T-18088-37

Print Number T-18088-36 (RT-1110)

Used to install the oil seal in the rear bearing housing.

SNAP RING INSTALLER Print Number T-16552-1-N

Used to install the snap ring in the output shaft quill.

(RT-I2515 Series)

BEARING DRIVERS Print Number T-18042 (Dimensions
for all drivers necessary on this print.)

Used to install bearings on shafts and in bores.

DRIVE GEAR BEARING NUT REMOVER

Print Number T-22553B
Print Number T-22553C (For push-type clutches)

Used to remove or install the drive gear bearing nut on the
shaft.

124

OUTPUT SHAFT HANGER BRACKET Make from yoke

stop nut and flat steel stock

Used to support the auxiliary section when installed or re-
moved from the front case in the vertical position.

Summary of Contents for RTX-12510































































































































Search results

Summary of Contents for RTX-12510

Reviews:

Related manuals for RTX-12510

Brands by name

Popular brands

Eaton RTX-12510, Service Manual

Search results

Summary of Contents for RTX-12510

Reviews:

Related manuals for RTX-12510

Brands by name

Popular brands