Eaton RTX-12510 Service Manual Download Page 32 | Manualshive

Page: 32 / 126

background image

c.

Removal and Disassembly of the Gear Shift Lever Housing

1. Turn out the four capscrews, jar lightly to break the

gasket seal and lift the gear shift lever assembly from the
shift bar housing.

4. Turn out the nut and remove the pivot pin from the

housing.

5. Remove the O-ring from the groove in the top of the

housing.

3.

Remove the tension spring washer and lever from the

housing.

32

2.

Remove the rubber dust cover from the lever and mount
the assembly in a vise by the housing. Free the tension
spring from the housing by inserting a large, heavy-
bladed scredriver between the spring and the housing
and twisting. Force the spring from under the lugs in the
housing one coil at a time.

«
...
30
31
32
33
34
...
»

Summary of Contents for RTX-12510































































































































Reviews:

No comments

Related manuals for RTX-12510

Brand: Panasonic Pages: 92

Brand: Panasonic Pages: 16

EXPEDITION XP40iw

Brand: Samson Pages: 2

Brand: Samson Pages: 40

Controlled Magnetic 444D

Brand: Shure Pages: 5

Brand: Marmitek Pages: 27

Brand: V2GO Pages: 4

Brand: Walimex Pro Pages: 10

Brand: Georg Neymann Pages: 10

Networked Paging Station-1

Brand: Biamp Pages: 16

Brand: IMG STAGE LINE Pages: 22

Brand: Hama Pages: 53

Brand: RCA Pages: 11

Brand: Waterous Pages: 4

Brand: Krüger & Matz Pages: 20

Brand: Curtis Pages: 12

Brand: Pioneer Pages: 63

MHC-GNX100, MHC-GNX90, MHC-GNX

Brand: Sony Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands